diff --git a/STYLE_GUIDE.md b/STYLE_GUIDE.md index 76709fc95a..1fba7bc276 100644 --- a/STYLE_GUIDE.md +++ b/STYLE_GUIDE.md @@ -172,6 +172,16 @@ where the Apollo installer has no equivalent: TEMP-1 Revision 1 firmware. The LED-1 uses the official WLED installer at `https://install.wled.me/`. +**Boot mode with two buttons.** When a step uses both the boot and reset +buttons, write the order as three bullets (press and hold **boot**; while +still holding it, press and release **reset**; let go of **boot**), then a +`warning` admonition titled "Keep holding boot the whole time" that says +pressing **reset** alone only restarts the device. Put both before the +photo or clip. Clips of the sequence carry step captions ("1 Press and hold +BOOT", "2 Keep holding BOOT. Tap RESET.", "3 Let go of BOOT") so a reader +who only watches still holds boot. A customer once watched an uncaptioned +clip, saw a finger resting on the board, and pressed reset alone. + --- ## 6. Voice and structure diff --git a/docs/assets/btn-1-boot-mode-method-2.webp b/docs/assets/btn-1-boot-mode-method-2.webp index 75777e397e..3753721be2 100755 Binary files a/docs/assets/btn-1-boot-mode-method-2.webp and b/docs/assets/btn-1-boot-mode-method-2.webp differ diff --git a/docs/assets/cast-1-boot-mode-method-2.webp b/docs/assets/cast-1-boot-mode-method-2.webp index f644248d5f..270c2a4988 100644 Binary files a/docs/assets/cast-1-boot-mode-method-2.webp and b/docs/assets/cast-1-boot-mode-method-2.webp differ diff --git a/docs/assets/esphome-starter-kit-boot-mode.webp b/docs/assets/esphome-starter-kit-boot-mode.webp index 53768bbb8a..0a2ddaee10 100755 Binary files a/docs/assets/esphome-starter-kit-boot-mode.webp and b/docs/assets/esphome-starter-kit-boot-mode.webp differ diff --git a/docs/assets/h-2-boot-mode-method-2-boot-reset-buttons.webp b/docs/assets/h-2-boot-mode-method-2-boot-reset-buttons.webp index 86776840bb..21afc067db 100755 Binary files a/docs/assets/h-2-boot-mode-method-2-boot-reset-buttons.webp and b/docs/assets/h-2-boot-mode-method-2-boot-reset-buttons.webp differ diff --git a/docs/assets/pump-1-hold-boot-and-reset-button-video.webp b/docs/assets/pump-1-hold-boot-and-reset-button-video.webp index 7a060b4549..f48e657c3f 100755 Binary files a/docs/assets/pump-1-hold-boot-and-reset-button-video.webp and b/docs/assets/pump-1-hold-boot-and-reset-button-video.webp differ diff --git a/docs/homey/products/air1/troubleshooting/air1-boot-mode.md b/docs/homey/products/air1/troubleshooting/air1-boot-mode.md index 625fedf210..2a8e9f8896 100755 --- a/docs/homey/products/air1/troubleshooting/air1-boot-mode.md +++ b/docs/homey/products/air1/troubleshooting/air1-boot-mode.md @@ -21,13 +21,21 @@ You'll hold the boot button while you plug in the USB-C cable, so the device sta ## Method 2: Boot and reset buttons -You'll use the boot and reset buttons together to put the device into boot mode while it's plugged into your computer. +You'll plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot and reset buttons as shown in the image below. 2\. Plug it into your computer. -3\. Hold down the boot button, then press and release the reset button while keeping the boot button pressed. Finally, release the boot button. +3\. Put your AIR-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button, next to the USB-C port). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the AIR-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![AIR-1 reset and boot buttons boxed and labeled with arrows next to the USB-C port](/assets/air-1-reset-boot-buttons-arrows.jpg) diff --git a/docs/homey/products/msr2/troubleshooting/msr2-boot-mode.md b/docs/homey/products/msr2/troubleshooting/msr2-boot-mode.md index d3fed62fc4..456e8a0542 100755 --- a/docs/homey/products/msr2/troubleshooting/msr2-boot-mode.md +++ b/docs/homey/products/msr2/troubleshooting/msr2-boot-mode.md @@ -22,13 +22,21 @@ You'll hold the boot button while you plug in the USB-C cable. ## Method 2: Boot and reset buttons -You'll use the boot and reset buttons together while the device is plugged into your computer. +You'll plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot button (the right opening, shown in the image above) and the reset button (the left opening, shown in the image below). 2\. Plug it into your computer. -3\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your MSR-2 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the MSR-2. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![MSR-2 case side with a tool pointing at the left opening for the reset button](/assets/msr-2-reset-button.jpg) diff --git a/docs/homey/products/mtr1/troubleshooting/mtr1-boot-mode.md b/docs/homey/products/mtr1/troubleshooting/mtr1-boot-mode.md index 7f9def9c1e..429674dee9 100755 --- a/docs/homey/products/mtr1/troubleshooting/mtr1-boot-mode.md +++ b/docs/homey/products/mtr1/troubleshooting/mtr1-boot-mode.md @@ -22,13 +22,21 @@ You'll hold the boot button while you plug in the USB-C cable. ## Method 2: Boot and reset buttons -You'll use the boot and reset buttons together while the device is plugged into your computer. +You'll plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot button (the right opening, shown in the image above) and the reset button (the left opening, shown in the image below). 2\. Plug it into your computer. -3\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your MTR-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the MTR-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Tool pointing to the reset button opening on the side of the MTR-1 case](/assets/mtr-1-reset-button.jpg) diff --git a/docs/homey/products/plt1/troubleshooting/plt1-boot-mode.md b/docs/homey/products/plt1/troubleshooting/plt1-boot-mode.md index b661b45c78..c3d6c52474 100755 --- a/docs/homey/products/plt1/troubleshooting/plt1-boot-mode.md +++ b/docs/homey/products/plt1/troubleshooting/plt1-boot-mode.md @@ -22,13 +22,21 @@ You can put your device into boot mode with only the boot button and a USB-C cab ## Method 2: Boot and reset buttons -You can also put your device into boot mode by pressing the reset button while you hold the boot button. +You can also put your device into boot mode by holding the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot button (on the side, shown in the image above) and the reset button (near the USB-C port, shown in the image below). 2\. Plug it into your computer. -3\. Hold down the boot button, then press and release the reset button while keeping the boot button pressed. Finally, release the boot button. +3\. Put your PLT-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (on the side, shown in the image above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (near the USB-C port, shown in the image below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the PLT-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Top of the PLT-1 with the reset button circled next to the plugged in USB-C cable](/assets/screenshot-2024-10-23-at-12-35-01-pm.png) diff --git a/docs/homey/products/plt1b/troubleshooting/plt1b-boot-mode.md b/docs/homey/products/plt1b/troubleshooting/plt1b-boot-mode.md index ee6b30a6a4..d30e19e0fe 100755 --- a/docs/homey/products/plt1b/troubleshooting/plt1b-boot-mode.md +++ b/docs/homey/products/plt1b/troubleshooting/plt1b-boot-mode.md @@ -26,11 +26,19 @@ You can put your device into boot mode with only the boot button and a pin. ## Method 2: Boot and reset buttons -You can also put your device into boot mode by pressing the reset button while you hold the boot button. +You can also put your device into boot mode by holding the boot button down while you press and release the reset button. 1\. Plug in the device -2\. Press and hold the boot button, while holding it press and release the reset button, then release the boot button +2\. Put your PLT-1B in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (next to the USB-C port, shown in the images above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, shown in the images below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the PLT-1B. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Tool pointing to the reset button on the PLT-1B PCB](/assets/plt-boot-mode-pic-6.jpg) diff --git a/docs/homey/products/temp1/troubleshooting/temp1-boot-mode.md b/docs/homey/products/temp1/troubleshooting/temp1-boot-mode.md index 8080bf6350..d3b075eff2 100755 --- a/docs/homey/products/temp1/troubleshooting/temp1-boot-mode.md +++ b/docs/homey/products/temp1/troubleshooting/temp1-boot-mode.md @@ -28,12 +28,20 @@ If you prefer, please remove the lid by gently prying up on the small slit by th ## Method 2: Boot and reset buttons -You can also open the case and use the boot and reset buttons together to put your device into boot mode. +You can also open the case and put your device into boot mode by holding the boot button down while you press and release the reset button. 1\. Unplug the device and remove the case as shown in the images above 2\. Plug it into your computer. -3\. Hold down the boot button, then press and release the reset button while keeping the boot button pressed. Finally, release the boot button. +3\. Put your TEMP-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (labeled BOOT, shown above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, at the opposite end of the board from **boot**). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the TEMP-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. 4\. Continue with [uploading the firmware document](https://wiki.apolloautomation.com/homey/products/temp1/troubleshooting/temp1-code/). \ No newline at end of file diff --git a/docs/homey/products/temp1b/troubleshooting/temp1b-boot-mode.md b/docs/homey/products/temp1b/troubleshooting/temp1b-boot-mode.md index 1023f416e5..2180bac522 100755 --- a/docs/homey/products/temp1b/troubleshooting/temp1b-boot-mode.md +++ b/docs/homey/products/temp1b/troubleshooting/temp1b-boot-mode.md @@ -28,12 +28,20 @@ If you prefer, please remove the lid by gently prying up on the small slit by th ## Method 2: Boot and reset buttons -Use this method to put your device into boot mode with the case removed, using both the boot and reset buttons. +Use this method to put your device into boot mode with the case removed, by holding the boot button down while you press and release the reset button. 1\. Unplug the device and remove the case as shown in the images above 2\. Plug it into your computer. -3\. Hold down the boot button, then press and release the reset button while keeping the boot button pressed. Finally, release the boot button. +3\. Put your TEMP-1B in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (labeled BOOT, shown above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, at the opposite end of the board from **boot**). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the TEMP-1B. It goes into boot mode only when **boot** is held down while you press and release **reset**. 4\. Continue with [uploading the firmware document](https://wiki.apolloautomation.com/homey/products/temp1b/troubleshooting/temp1b-code/). \ No newline at end of file diff --git a/docs/products/ESPHome-Starter-Kit/setup/first-steps.md b/docs/products/ESPHome-Starter-Kit/setup/first-steps.md index 3542ebeb96..aaee2f2659 100755 --- a/docs/products/ESPHome-Starter-Kit/setup/first-steps.md +++ b/docs/products/ESPHome-Starter-Kit/setup/first-steps.md @@ -203,9 +203,17 @@ The device is required to be flashed via USB using the bootloader mode the very ![Plugging the USB-C cable into the ESP32-C6 board](../../../assets/esphome-starter-kit-plug-in-usb-c.webp) -2\. Hold down the boot button. While still holding the boot button, press and release the reset button, then release the boot button. +2\. Put your ESP32-C6 in boot mode. Use both buttons, in this order: -![Holding the BOOT button on the ESP32-C6 while pressing and releasing RESET](../../../assets/esphome-starter-kit-boot-mode.webp) +- Press and hold the **Boot** button (labeled BOOT on the board, to the left of the USB-C port when the cable points toward you). Keep holding it. +- While you're still holding **Boot**, press and release the **Reset** button (labeled RESET, to the right of the USB-C port). +- Let go of **Boot**. + +!!! warning "Keep holding Boot the whole time" + + Pressing **Reset** by itself only restarts the ESP32-C6. It goes into boot mode only when **Boot** is held down while you press and release **Reset**. + +![Animation with step captions: press and hold Boot on the ESP32-C6, keep holding it while you tap Reset, then let go of Boot](../../../assets/esphome-starter-kit-boot-mode.webp) 3\. Your device is now in boot mode. The ESP32-C6 will now stay in bootloader mode until you flash it. diff --git a/docs/products/air1/troubleshooting/air1-boot-mode.md b/docs/products/air1/troubleshooting/air1-boot-mode.md index 9e7a503895..6a7b8831e8 100755 --- a/docs/products/air1/troubleshooting/air1-boot-mode.md +++ b/docs/products/air1/troubleshooting/air1-boot-mode.md @@ -22,13 +22,21 @@ With this method, you hold the boot button while you plug in the USB-C cable. ## Method 2: Boot and reset buttons -With this method, you use the boot and reset buttons while the device is plugged into your computer. +With this method, you plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot and reset buttons as shown in the image below. 2\. Plug it into your computer. -3\. Hold down the boot button, then press and release the reset button while keeping the boot button pressed. Finally, release the boot button. +3\. Put your AIR-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button, next to the USB-C port). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the AIR-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![AIR-1 case with arrows labeling the reset button on the left and the boot button on the right](/assets/air-1-reset-boot-buttons-arrows.jpg) diff --git a/docs/products/btn1/troubleshooting/btn1-boot-mode.md b/docs/products/btn1/troubleshooting/btn1-boot-mode.md index b44210fb1d..ac41495ce5 100755 --- a/docs/products/btn1/troubleshooting/btn1-boot-mode.md +++ b/docs/products/btn1/troubleshooting/btn1-boot-mode.md @@ -22,7 +22,7 @@ This method puts your device into boot mode using only the boot button. ![Holding the BTN-1 boot button on the right while plugging in the USB-C cable](/assets/btn-1-boot-mode-method-1.webp) -4\. You are now ready to reflash your device! +3\. You are now ready to reflash your device! [Click here to go to the reflashing guide!](https://wiki.apolloautomation.com/products/btn1/troubleshooting/btn1-reflash/){ .md-button .md-button--primary } @@ -38,10 +38,18 @@ This method uses the boot and reset buttons, and it's the one to use if your dev ![Back of the BTN-1 with arrows labeling the reset button on the left and the boot button on the right](/assets/btn-1-reset-boot-buttons.png) -2\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your BTN-1 in boot mode. Use both buttons, in this order: -![Holding the BTN-1 boot button while pressing and releasing the reset button](/assets/btn-1-boot-mode-method-2.webp) +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. -3\. You are now ready to reflash your device! +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the BTN-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the BTN-1, keep holding it while you tap reset, then let go of boot](/assets/btn-1-boot-mode-method-2.webp) + +4\. You are now ready to reflash your device! [Click here to go to the reflashing guide!](https://wiki.apolloautomation.com/products/btn1/troubleshooting/btn1-reflash/){ .md-button .md-button--primary } \ No newline at end of file diff --git a/docs/products/btn1/troubleshooting/btn1-reflash.md b/docs/products/btn1/troubleshooting/btn1-reflash.md index d8985dbf83..bff88bb8aa 100755 --- a/docs/products/btn1/troubleshooting/btn1-reflash.md +++ b/docs/products/btn1/troubleshooting/btn1-reflash.md @@ -16,9 +16,17 @@ description: Step by step guide for reflashing The BTN-1. ![Back of the BTN-1 with arrows labeling the reset button on the left and the boot button on the right](/assets/btn-1-reset-boot-buttons.png) -3\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your BTN-1 in boot mode. Use both buttons, in this order: -![Holding the BTN-1 boot button while pressing and releasing the reset button](/assets/btn-1-boot-mode-method-2.webp) +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the BTN-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the BTN-1, keep holding it while you tap reset, then let go of boot](/assets/btn-1-boot-mode-method-2.webp) 4\. Open the Apollo BTN-1 installer in a Chromium-based browser such as Chrome or Edge and click **Connect & Install**. Select the open com port and click **Connect**. diff --git a/docs/products/cast1/troubleshooting/cast1-boot-mode.md b/docs/products/cast1/troubleshooting/cast1-boot-mode.md index a8c10f405a..4faa6da6cf 100644 --- a/docs/products/cast1/troubleshooting/cast1-boot-mode.md +++ b/docs/products/cast1/troubleshooting/cast1-boot-mode.md @@ -28,9 +28,17 @@ This method puts your device into boot mode with the boot and reset buttons. ![CAST-1 case with labels pointing to the boot button on the left and the reset button on the right](/assets/cast-1-boot-reset-buttons.webp) -3\. Hold down the **boot** button (on the left), then press and release the **reset** button (on the right) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your CAST-1 in boot mode. Use both buttons, in this order: -![Holding the CAST-1 boot button while pressing and releasing the reset button beside it](/assets/cast-1-boot-mode-method-2.webp) +- Press and hold the **boot** button (on the left). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (on the right). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the CAST-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the CAST-1, keep holding it while you tap reset, then let go of boot](/assets/cast-1-boot-mode-method-2.webp) 4\. You are now ready to reflash your device! diff --git a/docs/products/cast1/troubleshooting/cast1-reflash.md b/docs/products/cast1/troubleshooting/cast1-reflash.md index 908bdf6f24..71de282728 100644 --- a/docs/products/cast1/troubleshooting/cast1-reflash.md +++ b/docs/products/cast1/troubleshooting/cast1-reflash.md @@ -17,9 +17,17 @@ description: Step by step guide for reflashing The CAST-1. ![CAST-1 case with labels pointing to the boot button on the left and the reset button on the right](/assets/cast-1-boot-reset-buttons.webp) -3\. Put the CAST-1 into boot mode. Hold down the **boot** button (on the left), then press and release the **reset** button (on the right) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your CAST-1 in boot mode. Use both buttons, in this order: -![Holding the CAST-1 boot button while pressing and releasing the reset button beside it](/assets/cast-1-boot-mode-method-2.webp) +- Press and hold the **boot** button (on the left). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (on the right). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the CAST-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the CAST-1, keep holding it while you tap reset, then let go of boot](/assets/cast-1-boot-mode-method-2.webp) 4\. Open the Apollo CAST-1 Installer. diff --git a/docs/products/h1/boot-mode.md b/docs/products/h1/boot-mode.md index a5c9de82c0..6559e0a013 100755 --- a/docs/products/h1/boot-mode.md +++ b/docs/products/h1/boot-mode.md @@ -22,6 +22,14 @@ You can also enter boot mode with the boot and reset buttons while the device is 1\. Plug in the device -2\. Press and hold the boot button, while holding it press and release the reset button, then release the boot button +2\. Put your H-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (circled in the photo above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (also circled in the photo above). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the H-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. 3\. Continue with [uploading the firmware](https://wiki.apolloautomation.com/products/h1/reflash/) \ No newline at end of file diff --git a/docs/products/h2/troubleshooting/boot-mode.md b/docs/products/h2/troubleshooting/boot-mode.md index 6ccca32fbb..26c49a861d 100755 --- a/docs/products/h2/troubleshooting/boot-mode.md +++ b/docs/products/h2/troubleshooting/boot-mode.md @@ -34,9 +34,17 @@ You can also enter boot mode with the boot and reset buttons while the device is ![H-2 board with arrows marking the Reset button on the left and the Boot button on the right](/assets/h-2-reset-and-boot-buttons-labeled.png) -2\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +2\. Put your H-2 in boot mode. Use both buttons, in this order: -![Holding the H-2 boot button while pressing and releasing the reset button, with USB-C connected](/assets/h-2-boot-mode-method-2-boot-reset-buttons.webp) +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the H-2. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the H-2, keep holding it while you tap reset, then let go of boot](/assets/h-2-boot-mode-method-2-boot-reset-buttons.webp) 3\. You are now ready to reflash your device! diff --git a/docs/products/msr1/troubleshooting/msr1-boot-mode.md b/docs/products/msr1/troubleshooting/msr1-boot-mode.md index 435be0b4ba..16b3ed0240 100755 --- a/docs/products/msr1/troubleshooting/msr1-boot-mode.md +++ b/docs/products/msr1/troubleshooting/msr1-boot-mode.md @@ -22,13 +22,21 @@ You'll hold the boot button while you plug in the USB-C cable. ## Method 2: Boot and reset buttons -You'll use the boot and reset buttons together while the device is plugged into your computer. +You'll plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot and reset buttons as shown in the image below. 2\. Plug it into your computer. -3\. Hold down the boot button (the left button), then press and release the reset button (the right button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your MSR-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the left button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the right button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the MSR-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Bare MSR-1 board with arrows marking the Boot and Reset buttons along the top edge](/assets/msr-1-buttons.jpg) diff --git a/docs/products/msr2/troubleshooting/msr2-boot-mode.md b/docs/products/msr2/troubleshooting/msr2-boot-mode.md index 9733474148..3f38173730 100755 --- a/docs/products/msr2/troubleshooting/msr2-boot-mode.md +++ b/docs/products/msr2/troubleshooting/msr2-boot-mode.md @@ -22,13 +22,21 @@ You'll hold the boot button while you plug in the USB-C cable. ## Method 2: Boot and reset buttons -You'll use the boot and reset buttons together while the device is plugged into your computer. +You'll plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot button (the right opening, shown in the image above) and the reset button (the left opening, shown in the image below). 2\. Plug it into your computer. -3\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your MSR-2 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the MSR-2. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Tool pointing to the MSR-2 reset button opening, the left of the two small slots](/assets/msr-2-reset-button.jpg) diff --git a/docs/products/mtr1/troubleshooting/mtr1-boot-mode.md b/docs/products/mtr1/troubleshooting/mtr1-boot-mode.md index 47fa4c268b..6d5c0994e0 100755 --- a/docs/products/mtr1/troubleshooting/mtr1-boot-mode.md +++ b/docs/products/mtr1/troubleshooting/mtr1-boot-mode.md @@ -22,13 +22,21 @@ You'll hold the boot button while you plug in the USB-C cable. ## Method 2: Boot and reset buttons -You'll use the boot and reset buttons together while the device is plugged into your computer. +You'll plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot button (the right opening, shown in the image above) and the reset button (the left opening, shown in the image below). 2\. Plug it into your computer. -3\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your MTR-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the MTR-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Tool pointing to the MTR-1 reset button opening, the left of the two small slots](/assets/mtr-1-reset-button.jpg) diff --git a/docs/products/new-product-template/troubleshooting/productname-boot-mode.md b/docs/products/new-product-template/troubleshooting/productname-boot-mode.md index 8a6315552a..48c50917c8 100755 --- a/docs/products/new-product-template/troubleshooting/productname-boot-mode.md +++ b/docs/products/new-product-template/troubleshooting/productname-boot-mode.md @@ -36,9 +36,17 @@ You'll use the boot and reset buttons together while the device is plugged into ![PUMP-1 with red arrows labeling the reset button on the left and the boot button on the right](/assets/pump-1-buttons-labeled.jpg) -2\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +2\. Put your PUMP-1 in boot mode. Use both buttons, in this order: -![Holding the PUMP-1 boot button while pressing and releasing the reset button](/assets/pump-1-hold-boot-and-reset-button-video.webp) +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the PUMP-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the PUMP-1, keep holding it while you tap reset, then let go of boot](/assets/pump-1-hold-boot-and-reset-button-video.webp) 3\. You are now ready to reflash your device! diff --git a/docs/products/plt1/troubleshooting/plt1-boot-mode.md b/docs/products/plt1/troubleshooting/plt1-boot-mode.md index fe4d2c51ad..1bd94a4679 100755 --- a/docs/products/plt1/troubleshooting/plt1-boot-mode.md +++ b/docs/products/plt1/troubleshooting/plt1-boot-mode.md @@ -22,13 +22,21 @@ You can put your device into boot mode with only the boot button and a USB-C cab ## Method 2: Boot and reset buttons -You can also put your device into boot mode by pressing the reset button while you hold the boot button. +You can also put your device into boot mode by holding the boot button down while you press and release the reset button. 1\. Unplug the device and locate the boot button (on the side, shown in the image above) and the reset button (near the USB-C port, shown in the image below). 2\. Plug it into your computer. -3\. Hold down the boot button, then press and release the reset button while keeping the boot button pressed. Finally, release the boot button. +3\. Put your PLT-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (on the side, shown in the image above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (near the USB-C port, shown in the image below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the PLT-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![PLT-1 with a USB-C cable plugged in and the reset button circled in red below the port](/assets/screenshot-2024-10-23-at-12-35-01-pm.png) diff --git a/docs/products/plt1b/troubleshooting/plt1b-boot-mode.md b/docs/products/plt1b/troubleshooting/plt1b-boot-mode.md index 755eb88f45..f9c653178a 100755 --- a/docs/products/plt1b/troubleshooting/plt1b-boot-mode.md +++ b/docs/products/plt1b/troubleshooting/plt1b-boot-mode.md @@ -26,11 +26,19 @@ You can put your device into boot mode with only the boot button and a pin. ## Method 2: Boot and reset buttons -You can also put your device into boot mode by pressing the reset button while you hold the boot button. +You can also put your device into boot mode by holding the boot button down while you press and release the reset button. 1\. Plug in the device -2\. Press and hold the boot button, while holding it press and release the reset button, then release the boot button +2\. Put your PLT-1B in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (next to the USB-C port, shown in the images above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, shown in the images below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the PLT-1B. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Open PLT-1B case with tweezers pointing near the reset button labeled SW2 RST](/assets/plt-boot-mode-pic-6.jpg) diff --git a/docs/products/pump1/troubleshooting/pump1-boot-mode.md b/docs/products/pump1/troubleshooting/pump1-boot-mode.md index 8a6315552a..48c50917c8 100755 --- a/docs/products/pump1/troubleshooting/pump1-boot-mode.md +++ b/docs/products/pump1/troubleshooting/pump1-boot-mode.md @@ -36,9 +36,17 @@ You'll use the boot and reset buttons together while the device is plugged into ![PUMP-1 with red arrows labeling the reset button on the left and the boot button on the right](/assets/pump-1-buttons-labeled.jpg) -2\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +2\. Put your PUMP-1 in boot mode. Use both buttons, in this order: -![Holding the PUMP-1 boot button while pressing and releasing the reset button](/assets/pump-1-hold-boot-and-reset-button-video.webp) +- Press and hold the **boot** button (the right button). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the PUMP-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. + +![Animation with step captions: press and hold boot on the PUMP-1, keep holding it while you tap reset, then let go of boot](/assets/pump-1-hold-boot-and-reset-button-video.webp) 3\. You are now ready to reflash your device! diff --git a/docs/products/rpro1/troubleshooting/rpro1-boot-mode.md b/docs/products/rpro1/troubleshooting/rpro1-boot-mode.md index 8c0aab2685..8ee65f42ae 100755 --- a/docs/products/rpro1/troubleshooting/rpro1-boot-mode.md +++ b/docs/products/rpro1/troubleshooting/rpro1-boot-mode.md @@ -30,7 +30,7 @@ You'll open the case, then hold the boot button while you plug in the USB-C cabl ## Method 2: Boot and reset buttons -You'll open the case, then use the boot and reset buttons together to put the device into boot mode. +You'll open the case, plug the board into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug your R PRO-1 from power and remove the back. @@ -48,6 +48,14 @@ You'll open the case, then use the boot and reset buttons together to put the de ![Tool pointing to the RST1 reset button at the bottom left of the R PRO-1 PCB](/assets/r-pro-1-reset-button.jpg) -5\. Hold down the boot button (the right button), then press and release the reset button (the left button) while keeping the boot button pressed. Finally, release the boot button. +5\. Plug your R PRO-1 into your computer, then put it in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (the right button, shown in step 3). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (the left button, shown in step 4). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the R PRO-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. 6\. Continue with uploading the firmware document. \ No newline at end of file diff --git a/docs/products/temp1/troubleshooting/temp1-boot-mode.md b/docs/products/temp1/troubleshooting/temp1-boot-mode.md index 1cc706b7ed..76f0fffe46 100755 --- a/docs/products/temp1/troubleshooting/temp1-boot-mode.md +++ b/docs/products/temp1/troubleshooting/temp1-boot-mode.md @@ -28,13 +28,21 @@ If you prefer, please remove the lid by gently prying up on the small slit by th ## Method 2: Boot and reset buttons -You can also open the case and use the boot and reset buttons together to put your device into boot mode. +You can also open the case and put your device into boot mode by holding the boot button down while you press and release the reset button. 1\. Unplug the device and remove the case as shown in the images above 2\. Plug it into your computer. -3\. Hold down the boot button (shown above), then press and release the reset button (shown below) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your TEMP-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (labeled BOOT, shown above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, shown below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the TEMP-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![TEMP-1 with the lid removed and a tool pointing at the RST reset button](/assets/temp-1-reset-button-lid-off.jpg) diff --git a/docs/products/temp1b/troubleshooting/temp1b-boot-mode.md b/docs/products/temp1b/troubleshooting/temp1b-boot-mode.md index 2a1f773bcb..309eaaa7ab 100755 --- a/docs/products/temp1b/troubleshooting/temp1b-boot-mode.md +++ b/docs/products/temp1b/troubleshooting/temp1b-boot-mode.md @@ -28,13 +28,21 @@ If you prefer, please remove the lid by gently prying up on the small slit by th ## Method 2: Boot and reset buttons -You'll open the case and use the boot and reset buttons together while the device is plugged into your computer. +You'll open the case, plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and remove the case as shown in the images above 2\. Plug it into your computer. -3\. Hold down the boot button (shown above), then press and release the reset button (shown below) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your TEMP-1B in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (labeled BOOT, shown above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, shown below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the TEMP-1B. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![TEMP-1B with the lid off, tool pointing at the RST reset button](/assets/temp-1-reset-button-lid-off.jpg) diff --git a/docs/products/temppro1/troubleshooting/temp-pro1-boot-mode.md b/docs/products/temppro1/troubleshooting/temp-pro1-boot-mode.md index f369a42d02..f44fdc23a4 100755 --- a/docs/products/temppro1/troubleshooting/temp-pro1-boot-mode.md +++ b/docs/products/temppro1/troubleshooting/temp-pro1-boot-mode.md @@ -26,13 +26,21 @@ You'll remove the lid, then hold the boot button while you plug in the USB-C cab ## Method 2: Boot and reset buttons -You'll open the case and use the boot and reset buttons together while the device is plugged into your computer. +You'll open the case, plug the device into your computer, then hold the boot button down while you press and release the reset button. 1\. Unplug the device and remove the case as shown in the images above 2\. Plug it into your computer. -3\. Hold down the boot button (shown above), then press and release the reset button (shown below) while keeping the boot button pressed. Finally, release the boot button. +3\. Put your TEMP Pro-1 in boot mode. Use both buttons, in this order: + +- Press and hold the **boot** button (labeled BOOT, shown above). Keep holding it. +- While you're still holding **boot**, press and release the **reset** button (labeled RST, shown below). +- Let go of **boot**. + +!!! warning "Keep holding boot the whole time" + + Pressing **reset** by itself only restarts the TEMP Pro-1. It goes into boot mode only when **boot** is held down while you press and release **reset**. ![Tool pointing at the RST reset button on the TEMP Pro-1 board](/assets/temp-pro-1-reset-button.jpeg)