drm/bridge: ti-sn65dsi86: Add HPD for DisplayPort connector type

By default, HPD was disabled on SN65DSI86 bridge. When the driver was
added (commit "a095f15c00e27"), the HPD_DISABLE bit was set in pre-enable
call which was moved to other function calls subsequently.
Later on, commit "c312b0df3b13" added detect utility for DP mode. But with
HPD_DISABLE bit set, all the HPD events are disabled[0] and the debounced
state always return 1 (always connected state).

Set HPD_DISABLE bit conditionally based on display sink's connector type.
Since the HPD_STATE is reflected correctly only after waiting for debounce
time (~100-400ms) and adding this delay in detect() is not feasible
owing to the performace impact (glitches and frame drop), remove runtime
calls in detect() and add hpd_enable()/disable() bridge hooks with runtime
calls, to detect hpd properly without any delay.

[0]: <https://www.ti.com/lit/gpn/SN65DSI86> (Pg. 32)

Fixes: c312b0d ("drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP")
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250624044835.165708-1-j-choudhary@ti.com

Author: jayesh-ti

drivers/gpu/drm/bridge/ti-sn65dsi86.c

@@ -348,12 +348,18 @@ static void ti_sn65dsi86_enable_comms(struct ti_sn65dsi86 *pdata,
 	 * 200 ms.  We'll assume that the panel driver will have the hardcoded
 	 * delay in its prepare and always disable HPD.
 	 *
-	 * If HPD somehow makes sense on some future panel we'll have to
-	 * change this to be conditional on someone specifying that HPD should
-	 * be used.
+	 * For DisplayPort bridge type, we need HPD. So we use the bridge type
+	 * to conditionally disable HPD.
+	 * NOTE: The bridge type is set in ti_sn_bridge_probe() but enable_comms()
+	 * can be called before. So for DisplayPort, HPD will be enabled once
+	 * bridge type is set. We are using bridge type instead of "no-hpd"
+	 * property because it is not used properly in devicetree description
+	 * and hence is unreliable.
 	 */
-	regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG, HPD_DISABLE,
-			   HPD_DISABLE);
+
+	if (pdata->bridge.type != DRM_MODE_CONNECTOR_DisplayPort)
+		regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG, HPD_DISABLE,
+				   HPD_DISABLE);
 
 	pdata->comms_enabled = true;
 
@@ -1195,9 +1201,14 @@ static enum drm_connector_status ti_sn_bridge_detect(struct drm_bridge *bridge)
 	struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge);
 	int val = 0;
 
-	pm_runtime_get_sync(pdata->dev);
+	/*
+	 * Runtime reference is grabbed in ti_sn_bridge_hpd_enable()
+	 * as the chip won't report HPD just after being powered on.
+	 * HPD_DEBOUNCED_STATE reflects correct state only after the
+	 * debounce time (~100-400 ms).
+	 */
+
 	regmap_read(pdata->regmap, SN_HPD_DISABLE_REG, &val);
-	pm_runtime_put_autosuspend(pdata->dev);
 
 	return val & HPD_DEBOUNCED_STATE ? connector_status_connected
 					 : connector_status_disconnected;
@@ -1220,6 +1231,26 @@ static void ti_sn65dsi86_debugfs_init(struct drm_bridge *bridge, struct dentry *
 	debugfs_create_file("status", 0600, debugfs, pdata, &status_fops);
 }
 
+static void ti_sn_bridge_hpd_enable(struct drm_bridge *bridge)
+{
+	struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge);
+
+	/*
+	 * Device needs to be powered on before reading the HPD state
+	 * for reliable hpd detection in ti_sn_bridge_detect() due to
+	 * the high debounce time.
+	 */
+
+	pm_runtime_get_sync(pdata->dev);
+}
+
+static void ti_sn_bridge_hpd_disable(struct drm_bridge *bridge)
+{
+	struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge);
+
+	pm_runtime_put_autosuspend(pdata->dev);
+}
+
 static const struct drm_bridge_funcs ti_sn_bridge_funcs = {
 	.attach = ti_sn_bridge_attach,
 	.detach = ti_sn_bridge_detach,
@@ -1234,6 +1265,8 @@ static const struct drm_bridge_funcs ti_sn_bridge_funcs = {
 	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
 	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
 	.debugfs_init = ti_sn65dsi86_debugfs_init,
+	.hpd_enable = ti_sn_bridge_hpd_enable,
+	.hpd_disable = ti_sn_bridge_hpd_disable,
 };
 
 static void ti_sn_bridge_parse_lanes(struct ti_sn65dsi86 *pdata,
@@ -1321,8 +1354,26 @@ static int ti_sn_bridge_probe(struct auxiliary_device *adev,
 	pdata->bridge.type = pdata->next_bridge->type == DRM_MODE_CONNECTOR_DisplayPort
 			   ? DRM_MODE_CONNECTOR_DisplayPort : DRM_MODE_CONNECTOR_eDP;
 
-	if (pdata->bridge.type == DRM_MODE_CONNECTOR_DisplayPort)
-		pdata->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_DETECT;
+	if (pdata->bridge.type == DRM_MODE_CONNECTOR_DisplayPort) {
+		pdata->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_DETECT |
+				    DRM_BRIDGE_OP_HPD;
+		/*
+		 * If comms were already enabled they would have been enabled
+		 * with the wrong value of HPD_DISABLE. Update it now. Comms
+		 * could be enabled if anyone is holding a pm_runtime reference
+		 * (like if a GPIO is in use). Note that in most cases nobody
+		 * is doing AUX channel xfers before the bridge is added so
+		 * HPD doesn't _really_ matter then. The only exception is in
+		 * the eDP case where the panel wants to read the EDID before
+		 * the bridge is added. We always consistently have HPD disabled
+		 * for eDP.
+		 */
+		mutex_lock(&pdata->comms_mutex);
+		if (pdata->comms_enabled)
+			regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG,
+					   HPD_DISABLE, 0);
+		mutex_unlock(&pdata->comms_mutex);
+	};
 
 	drm_bridge_add(&pdata->bridge);