arm64: dts: ti: k3-am654-base-board: add boot phase tags

The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used in the bootloader for the
AM654 reference board.

UARTs used as a console, the SD and eMMC nodes along with the needed
regulators for UHS modes, and the needed nodes for OSPI boot are all
marked with 'bootph-all' to handle the various boot modes the board is
capable of

Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-65-boot-phases-v2-2-d431deb88783@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Author: bryanbrattlof

arch/arm64/boot/dts/ti/k3-am654-base-board.dts

@@ -144,6 +144,7 @@
 		regulator-boot-on;
 		vin-supply = <&vcc3v3_io>;
 		gpio = <&wkup_gpio0 28 GPIO_ACTIVE_HIGH>;
+		bootph-all;
 	};
 };
 
@@ -155,19 +156,22 @@
 			AM65X_WKUP_IOPAD(0x00c8, PIN_INPUT, 1)	/* (AC2) WKUP_GPIO0_6.WKUP_UART0_CTSn */
 			AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 1)	/* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */
 		>;
+		bootph-all;
 	};
 
 	ddr_vtt_pins_default: ddr-vtt-default-pins {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7)	/* WKUP_GPIO0_28 */
 		>;
+		bootph-all;
 	};
 
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) /* (AC7) WKUP_I2C0_SCL */
 			AM65X_WKUP_IOPAD(0x00e4, PIN_INPUT, 0) /* (AD6) WKUP_I2C0_SDA */
 		>;
+		bootph-all;
 	};
 
 	push_button_pins_default: push-button-default-pins {
@@ -191,6 +195,7 @@
 			AM65X_WKUP_IOPAD(0x0028, PIN_INPUT, 0)  /* (R3) MCU_OSPI0_D7 */
 			AM65X_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* (R4) MCU_OSPI0_CSn0 */
 		>;
+		bootph-all;
 	};
 
 	wkup_pca554_default: wkup-pca554-default-pins {
@@ -206,6 +211,7 @@
 			AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 4)	/* (P1) MCU_OSPI1_D3.MCU_UART0_CTSn */
 			AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 4)	/* (N3) MCU_OSPI1_CSn1.MCU_UART0_RTSn */
 		>;
+		bootph-all;
 	};
 
 	mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -248,6 +254,7 @@
 			AM65X_IOPAD(0x01ec, PIN_INPUT, 0)	/* (AG11) UART0_CTSn */
 			AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0)	/* (AD11) UART0_RTSn */
 		>;
+		bootph-all;
 	};
 
 	main_i2c2_pins_default: main-i2c2-default-pins {
@@ -281,6 +288,7 @@
 			AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP, 0) /* (A23) MMC0_SDCD */
 			AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */
 		>;
+		bootph-all;
 	};
 
 	main_mmc1_pins_default: main-mmc1-default-pins {
@@ -294,6 +302,7 @@
 			AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */
 			AM65X_IOPAD(0x02e0, PIN_INPUT, 0) /* (C24) MMC1_SDWP */
 		>;
+		bootph-all;
 	};
 
 	usb1_pins_default: usb1-default-pins {
@@ -343,6 +352,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
 	power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+	bootph-all;
 };
 
 &wkup_i2c0 {
@@ -368,6 +378,7 @@
 		ti,vsel0-state-high;
 		ti,vsel1-state-high;
 		ti,enable-vout-discharge;
+		bootph-all;
 	};
 
 	gpio@38 {
@@ -456,6 +467,7 @@
 	bus-width = <8>;
 	non-removable;
 	ti,driver-strength-ohm = <50>;
+	bootph-all;
 };
 
 /*
@@ -470,6 +482,7 @@
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
+	bootph-all;
 };
 
 &usb1 {
@@ -630,3 +643,7 @@
 &dss {
 	status = "disabled";
 };
+
+&wkup_gpio0 {
+	bootph-all;
+};

arch/arm64/boot/dts/ti/k3-am654-pcie-usb2.dtso

@@ -46,6 +46,7 @@
 
 &dwc3_0 {
 	status = "okay";
+	bootph-all;
 };
 
 &usb0_phy {

arch/arm64/boot/dts/ti/k3-am654-pcie-usb3.dtso

@@ -45,6 +45,7 @@
 	<&k3_clks 151 8>;      /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
 	phys = <&serdes0 PHY_TYPE_USB3 0>;
 	phy-names = "usb3-phy";
+	bootph-all;
 };
 
 &usb0 {