Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull pci updates from Bjorn Helgaas:
 "Enumeration:
   - Conserve IRQs by setting up portdrv IRQs only when there are users
     (Jan Kiszka)
   - Rework and simplify _OSC negotiation for control of PCIe features
     (Joerg Roedel)
   - Remove struct pci_dev.driver pointer since it's redundant with the
     struct device.driver pointer (Uwe Kleine-König)

  Resource management:
   - Coalesce contiguous host bridge apertures from _CRS to accommodate
     BARs that cover more than one aperture (Kai-Heng Feng)

  Sysfs:
   - Check CAP_SYS_ADMIN before parsing user input (Krzysztof
     Wilczyński)
   - Return -EINVAL consistently from "store" functions (Krzysztof
     Wilczyński)
   - Use sysfs_emit() in endpoint "show" functions to avoid buffer
     overruns (Kunihiko Hayashi)

  PCIe native device hotplug:
   - Ignore Link Down/Up caused by resets during error recovery so
     endpoint drivers can remain bound to the device (Lukas Wunner)

  Virtualization:
   - Avoid bus resets on Atheros QCA6174, where they hang the device
     (Ingmar Klein)
   - Work around Pericom PI7C9X2G switch packet drop erratum by using
     store and forward mode instead of cut-through (Nathan Rossi)
   - Avoid trying to enable AtomicOps on VFs; the PF setting applies to
     all VFs (Selvin Xavier)

  MSI:
   - Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
     interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
     Song)

  VPD:
   - Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
     in the possible VPD space; use these to simplify the cxgb3 driver
     (Heiner Kallweit)

  Peer-to-peer DMA:
   - Add (not subtract) the bus offset when calculating DMA address
     (Wang Lu)

  ASPM:
   - Re-enable LTR at Downstream Ports so they don't report Unsupported
     Requests when reset or hot-added devices send LTR messages
     (Mingchuang Qiao)

  Apple PCIe controller driver:
   - Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
     Zyngier)

  Cadence PCIe controller driver:
   - Return success when probe succeeds instead of falling into error
     path (Li Chen)

  HiSilicon Kirin PCIe controller driver:
   - Reorganize PHY logic and add support for external PHY drivers
     (Mauro Carvalho Chehab)
   - Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
     Carvalho Chehab)
   - Add Kirin 970 support (Mauro Carvalho Chehab)
   - Make driver removable (Mauro Carvalho Chehab)

  Intel VMD host bridge driver:
   - If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
     enabled (Adrian Huang)
   - Number each controller so we can tell them apart in
     /proc/interrupts (Chunguang Xu)
   - Avoid building on UML because VMD depends on x86 bare metal APIs
     (Johannes Berg)

  Marvell Aardvark PCIe controller driver:
   - Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
   - Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
   - Downgrade PIO Response Status messages to debug level (Marek Behún)
   - Preserve CRS SV (Config Request Retry Software Visibility) bit in
     emulated Root Control register (Pali Rohár)
   - Fix issue in configuring reference clock (Pali Rohár)
   - Don't clear status bits for masked interrupts (Pali Rohár)
   - Don't mask unused interrupts (Pali Rohár)
   - Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
   - Retry config accesses on CRS response (Pali Rohár)
   - Simplify emulated Root Capabilities initialization (Pali Rohár)
   - Fix several link training issues (Pali Rohár)
   - Fix link-up checking via LTSSM (Pali Rohár)
   - Fix reporting of Data Link Layer Link Active (Pali Rohár)
   - Fix emulation of W1C bits (Marek Behún)
   - Fix MSI domain .alloc() method to return zero on success (Marek
     Behún)
   - Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
     (Marek Behún)
   - Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
     at startup; PCI core will set those as necessary (Pali Rohár)
   - When operating as a Root Port, set class code to "PCI Bridge"
     instead of the default "Mass Storage Controller" (Pali Rohár)
   - Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
     implement this per spec (Pali Rohár)
   - Add emulation of option ROM BAR since aardvark doesn't implement
     this per spec (Pali Rohár)

  MediaTek MT7621 PCIe controller driver:
   - Add MediaTek MT7621 PCIe host controller driver and DT binding
     (Sergio Paracuellos)

  Qualcomm PCIe controller driver:
   - Add SC8180x compatible string (Bjorn Andersson)
   - Add endpoint controller driver and DT binding (Manivannan
     Sadhasivam)
   - Restructure to use of_device_get_match_data() (Prasad Malisetty)
   - Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)

  Renesas R-Car PCIe controller driver:
   - Remove unnecessary includes (Geert Uytterhoeven)

  Rockchip DesignWare PCIe controller driver:
   - Add DT binding (Simon Xue)

  Socionext UniPhier Pro5 controller driver:
   - Serialize INTx masking/unmasking (Kunihiko Hayashi)

  Synopsys DesignWare PCIe controller driver:
   - Run dwc .host_init() method before registering MSI interrupt
     handler so we can deal with pending interrupts left by bootloader
     (Bjorn Andersson)
   - Clean up Kconfig dependencies (Andy Shevchenko)
   - Export symbols to allow more modular drivers (Luca Ceresoli)

  TI DRA7xx PCIe controller driver:
   - Allow host and endpoint drivers to be modules (Luca Ceresoli)
   - Enable external clock if present (Luca Ceresoli)

  TI J721E PCIe driver:
   - Disable PHY when probe fails after initializing it (Christophe
     JAILLET)

  MicroSemi Switchtec management driver:
   - Return error to application when command execution fails because an
     out-of-band reset has cleared the device BARs, Memory Space Enable,
     etc (Kelvin Cao)
   - Fix MRPC error status handling issue (Kelvin Cao)
   - Mask out other bits when reading of management VEP instance ID
     (Kelvin Cao)
   - Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
     (Kelvin Cao)
   - Add check of event support (Logan Gunthorpe)

  Miscellaneous:
   - Remove unused pci_pool wrappers, which have been replaced by
     dma_pool (Cai Huoqing)
   - Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
     Wilczyński)
   - Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
     Wilczyński)
   - Fix some sscanf(), sprintf() format mismatches (Krzysztof
     Wilczyński)
   - Update PCI subsystem information in MAINTAINERS (Krzysztof
     Wilczyński)
   - Correct some misspellings (Krzysztof Wilczyński)"

* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
  PCI: Add ACS quirk for Pericom PI7C9X2G switches
  PCI: apple: Configure RID to SID mapper on device addition
  iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
  PCI: apple: Implement MSI support
  PCI: apple: Add INTx and per-port interrupt support
  PCI: kirin: Allow removing the driver
  PCI: kirin: De-init the dwc driver
  PCI: kirin: Disable clkreq during poweroff sequence
  PCI: kirin: Move the power-off code to a common routine
  PCI: kirin: Add power_off support for Kirin 960 PHY
  PCI: kirin: Allow building it as a module
  PCI: kirin: Add MODULE_* macros
  PCI: kirin: Add Kirin 970 compatible
  PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
  PCI: apple: Set up reference clocks when probing
  PCI: apple: Add initial hardware bring-up
  PCI: of: Allow matching of an interrupt-map local to a PCI device
  of/irq: Allow matching of an interrupt-map local to an interrupt controller
  irqdomain: Make of_phandle_args_to_fwspec() generally available
  PCI: Do not enable AtomicOps on VFs
  ...

Author: torvalds

Documentation/ABI/testing/sysfs-bus-pci

@@ -100,6 +100,17 @@ Description:
 		This attribute indicates the mode that the irq vector named by
 		the file is in (msi vs. msix)
 
+What:		/sys/bus/pci/devices/.../irq
+Date:		August 2021
+Contact:	Linux PCI developers <linux-pci@vger.kernel.org>
+Description:
+		If a driver has enabled MSI (not MSI-X), "irq" contains the
+		IRQ of the first MSI vector. Otherwise "irq" contains the
+		IRQ of the legacy INTx interrupt.
+
+		"irq" being set to 0 indicates that the device isn't
+		capable of generating legacy INTx interrupts.
+
 What:		/sys/bus/pci/devices/.../remove
 Date:		January 2009
 Contact:	Linux PCI developers <linux-pci@vger.kernel.org>

Documentation/devicetree/bindings/pci/mediatek,mt7621-pcie.yaml

@@ -0,0 +1,142 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/mediatek,mt7621-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT7621 PCIe controller
+
+maintainers:
+  - Sergio Paracuellos <sergio.paracuellos@gmail.com>
+
+description: |+
+  MediaTek MT7621 PCIe subsys supports a single Root Complex (RC)
+  with 3 Root Ports. Each Root Port supports a Gen1 1-lane Link
+
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+  compatible:
+    const: mediatek,mt7621-pci
+
+  reg:
+    items:
+      - description: host-pci bridge registers
+      - description: pcie port 0 RC control registers
+      - description: pcie port 1 RC control registers
+      - description: pcie port 2 RC control registers
+
+  ranges:
+    maxItems: 2
+
+patternProperties:
+  'pcie@[0-2],0':
+    type: object
+    $ref: /schemas/pci/pci-bus.yaml#
+
+    properties:
+      resets:
+        maxItems: 1
+
+      clocks:
+        maxItems: 1
+
+      phys:
+        maxItems: 1
+
+    required:
+      - "#interrupt-cells"
+      - interrupt-map-mask
+      - interrupt-map
+      - resets
+      - clocks
+      - phys
+      - phy-names
+      - ranges
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - ranges
+  - "#interrupt-cells"
+  - interrupt-map-mask
+  - interrupt-map
+  - reset-gpios
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/mips-gic.h>
+
+    pcie: pcie@1e140000 {
+        compatible = "mediatek,mt7621-pci";
+        reg = <0x1e140000 0x100>,
+              <0x1e142000 0x100>,
+              <0x1e143000 0x100>,
+              <0x1e144000 0x100>;
+
+        #address-cells = <3>;
+        #size-cells = <2>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&pcie_pins>;
+        device_type = "pci";
+        ranges = <0x02000000 0 0x60000000 0x60000000 0 0x10000000>,  /* pci memory */
+                 <0x01000000 0 0x1e160000 0x1e160000 0 0x00010000>;  /* io space */
+        #interrupt-cells = <1>;
+        interrupt-map-mask = <0xF800 0 0 0>;
+        interrupt-map = <0x0000 0 0 0 &gic GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0800 0 0 0 &gic GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x1000 0 0 0 &gic GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
+        reset-gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+
+        pcie@0,0 {
+            reg = <0x0000 0 0 0 0>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            device_type = "pci";
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 0>;
+            interrupt-map = <0 0 0 0 &gic GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>;
+            resets = <&rstctrl 24>;
+            clocks = <&clkctrl 24>;
+            phys = <&pcie0_phy 1>;
+            phy-names = "pcie-phy0";
+            ranges;
+        };
+
+        pcie@1,0 {
+            reg = <0x0800 0 0 0 0>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            device_type = "pci";
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 0>;
+            interrupt-map = <0 0 0 0 &gic GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>;
+            resets = <&rstctrl 25>;
+            clocks = <&clkctrl 25>;
+            phys = <&pcie0_phy 1>;
+            phy-names = "pcie-phy1";
+            ranges;
+        };
+
+        pcie@2,0 {
+            reg = <0x1000 0 0 0 0>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            device_type = "pci";
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 0>;
+            interrupt-map = <0 0 0 0 &gic GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
+            resets = <&rstctrl 26>;
+            clocks = <&clkctrl 26>;
+            phys = <&pcie2_phy 0>;
+            phy-names = "pcie-phy2";
+            ranges;
+        };
+    };
+...

Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml

@@ -0,0 +1,158 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PCIe Endpoint Controller binding
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+allOf:
+  - $ref: "pci-ep.yaml#"
+
+properties:
+  compatible:
+    const: qcom,sdx55-pcie-ep
+
+  reg:
+    items:
+      - description: Qualcomm-specific PARF configuration registers
+      - description: DesignWare PCIe registers
+      - description: External local bus interface registers
+      - description: Address Translation Unit (ATU) registers
+      - description: Memory region used to map remote RC address space
+      - description: BAR memory region
+
+  reg-names:
+    items:
+      - const: parf
+      - const: dbi
+      - const: elbi
+      - const: atu
+      - const: addr_space
+      - const: mmio
+
+  clocks:
+    items:
+      - description: PCIe Auxiliary clock
+      - description: PCIe CFG AHB clock
+      - description: PCIe Master AXI clock
+      - description: PCIe Slave AXI clock
+      - description: PCIe Slave Q2A AXI clock
+      - description: PCIe Sleep clock
+      - description: PCIe Reference clock
+
+  clock-names:
+    items:
+      - const: aux
+      - const: cfg
+      - const: bus_master
+      - const: bus_slave
+      - const: slave_q2a
+      - const: sleep
+      - const: ref
+
+  qcom,perst-regs:
+    description: Reference to a syscon representing TCSR followed by the two
+                 offsets within syscon for Perst enable and Perst separation
+                 enable registers
+    $ref: "/schemas/types.yaml#/definitions/phandle-array"
+    items:
+      minItems: 3
+      maxItems: 3
+
+  interrupts:
+    items:
+      - description: PCIe Global interrupt
+      - description: PCIe Doorbell interrupt
+
+  interrupt-names:
+    items:
+      - const: global
+      - const: doorbell
+
+  reset-gpios:
+    description: GPIO used as PERST# input signal
+    maxItems: 1
+
+  wake-gpios:
+    description: GPIO used as WAKE# output signal
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: core
+
+  power-domains:
+    maxItems: 1
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: pciephy
+
+  num-lanes:
+    default: 2
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+  - qcom,perst-regs
+  - interrupts
+  - interrupt-names
+  - reset-gpios
+  - resets
+  - reset-names
+  - power-domains
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sdx55.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    pcie_ep: pcie-ep@40000000 {
+        compatible = "qcom,sdx55-pcie-ep";
+        reg = <0x01c00000 0x3000>,
+              <0x40000000 0xf1d>,
+              <0x40000f20 0xc8>,
+              <0x40001000 0x1000>,
+              <0x40002000 0x1000>,
+              <0x01c03000 0x3000>;
+        reg-names = "parf", "dbi", "elbi", "atu", "addr_space",
+                    "mmio";
+
+        clocks = <&gcc GCC_PCIE_AUX_CLK>,
+             <&gcc GCC_PCIE_CFG_AHB_CLK>,
+             <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+             <&gcc GCC_PCIE_SLV_AXI_CLK>,
+             <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+             <&gcc GCC_PCIE_SLEEP_CLK>,
+             <&gcc GCC_PCIE_0_CLKREF_CLK>;
+        clock-names = "aux", "cfg", "bus_master", "bus_slave",
+                      "slave_q2a", "sleep", "ref";
+
+        qcom,perst-regs = <&tcsr 0xb258 0xb270>;
+
+        interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "global", "doorbell";
+        reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+        wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+        resets = <&gcc GCC_PCIE_BCR>;
+        reset-names = "core";
+        power-domains = <&gcc PCIE_GDSC>;
+        phys = <&pcie0_lane>;
+        phy-names = "pciephy";
+        max-link-speed = <3>;
+        num-lanes = <2>;
+    };

Documentation/devicetree/bindings/pci/qcom,pcie.txt

@@ -12,6 +12,7 @@
 			- "qcom,pcie-ipq4019" for ipq4019
 			- "qcom,pcie-ipq8074" for ipq8074
 			- "qcom,pcie-qcs404" for qcs404
+			- "qcom,pcie-sc8180x" for sc8180x
 			- "qcom,pcie-sdm845" for sdm845
 			- "qcom,pcie-sm8250" for sm8250
 			- "qcom,pcie-ipq6018" for ipq6018
@@ -156,7 +157,7 @@
 			- "pipe"	PIPE clock
 
 - clock-names:
-	Usage: required for sm8250
+	Usage: required for sc8180x and sm8250
 	Value type: <stringlist>
 	Definition: Should contain the following entries
 			- "aux"		Auxiliary clock
@@ -245,7 +246,7 @@
 			- "ahb"			AHB reset
 
 - reset-names:
-	Usage: required for sdm845 and sm8250
+	Usage: required for sc8180x, sdm845 and sm8250
 	Value type: <stringlist>
 	Definition: Should contain the following entries
 			- "pci"			PCIe core reset