dt-bindings: Drop unnecessary quotes on keys

The yamllint quoted-strings check wasn't checking keys for quotes, but
support for checking keys was added in 1.34 release. Fix all the errors
found when enabling the check.

Clean-up the xilinx-versal-cpm formatting while we're here.

Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240426202239.2837516-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>

Author: robherring

Documentation/devicetree/bindings/net/sff,sfp.yaml

@@ -29,39 +29,39 @@ properties:
       allowable by a module in the slot, in milli-Watts. Presently, modules can
       be up to 1W, 1.5W or 2W.
 
-  "mod-def0-gpios":
+  mod-def0-gpios:
     maxItems: 1
     description:
       GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module
       presence input gpio signal, active (module absent) high. Must not be
       present for SFF modules
 
-  "los-gpios":
+  los-gpios:
     maxItems: 1
     description:
       GPIO phandle and a specifier of the Receiver Loss of Signal Indication
       input gpio signal, active (signal lost) high
 
-  "tx-fault-gpios":
+  tx-fault-gpios:
     maxItems: 1
     description:
       GPIO phandle and a specifier of the Module Transmitter Fault input gpio
       signal, active (fault condition) high
 
-  "tx-disable-gpios":
+  tx-disable-gpios:
     maxItems: 1
     description:
       GPIO phandle and a specifier of the Transmitter Disable output gpio
       signal, active (Tx disable) high
 
-  "rate-select0-gpios":
+  rate-select0-gpios:
     maxItems: 1
     description:
       GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0)
       output gpio signal, low - low Rx rate, high - high Rx rate Must not be
       present for SFF modules
 
-  "rate-select1-gpios":
+  rate-select1-gpios:
     maxItems: 1
     description:
       GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1)

Documentation/devicetree/bindings/pci/xilinx-versal-cpm.yaml

@@ -48,13 +48,16 @@ properties:
   interrupt-controller:
     description: Interrupt controller node for handling legacy PCI interrupts.
     type: object
+    additionalProperties: false
+
     properties:
       "#address-cells":
         const: 0
+
       "#interrupt-cells":
         const: 1
-      "interrupt-controller": true
-    additionalProperties: false
+
+      interrupt-controller: true
 
 required:
   - reg

Documentation/devicetree/bindings/pci/xlnx,nwl-pcie.yaml

@@ -84,7 +84,7 @@ properties:
       "#interrupt-cells":
         const: 1
 
-      "interrupt-controller": true
+      interrupt-controller: true
 
     required:
       - "#address-cells"

Documentation/devicetree/bindings/phy/brcm,sata-phy.yaml

@@ -59,14 +59,14 @@ patternProperties:
       "#phy-cells":
         const: 0
 
-      "brcm,enable-ssc":
+      brcm,enable-ssc:
         $ref: /schemas/types.yaml#/definitions/flag
         description: |
           Use spread spectrum clocking (SSC) on this port
           This property is not applicable for "brcm,iproc-ns2-sata-phy",
           "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy".
 
-      "brcm,rxaeq-mode":
+      brcm,rxaeq-mode:
         $ref: /schemas/types.yaml#/definitions/string
         description:
           String that indicates the desired RX equalizer mode.
@@ -75,15 +75,15 @@ patternProperties:
           - auto
           - manual
 
-      "brcm,rxaeq-value":
+      brcm,rxaeq-value:
         $ref: /schemas/types.yaml#/definitions/uint32
         description: |
             When 'brcm,rxaeq-mode' is set to "manual", provides the RX
             equalizer value that should be used.
         minimum: 0
         maximum: 63
 
-      "brcm,tx-amplitude-millivolt":
+      brcm,tx-amplitude-millivolt:
         description: |
             Transmit amplitude voltage in millivolt.
         $ref: /schemas/types.yaml#/definitions/uint32

Documentation/devicetree/bindings/regulator/ti,tps62864.yaml

@@ -24,7 +24,7 @@ properties:
     type: object
 
     properties:
-      "SW":
+      SW:
         type: object
         $ref: regulator.yaml#
         unevaluatedProperties: false

Documentation/devicetree/bindings/soc/tegra/nvidia,tegra20-pmc.yaml

@@ -365,9 +365,9 @@ allOf:
 additionalProperties: false
 
 dependencies:
-  "nvidia,suspend-mode": ["nvidia,core-pwr-off-time", "nvidia,cpu-pwr-off-time"]
-  "nvidia,core-pwr-off-time": ["nvidia,core-pwr-good-time"]
-  "nvidia,cpu-pwr-off-time": ["nvidia,cpu-pwr-good-time"]
+  nvidia,suspend-mode: ["nvidia,core-pwr-off-time", "nvidia,cpu-pwr-off-time"]
+  nvidia,core-pwr-off-time: ["nvidia,core-pwr-good-time"]
+  nvidia,cpu-pwr-off-time: ["nvidia,cpu-pwr-good-time"]
 
 examples:
   - |

Documentation/devicetree/bindings/tpm/ibm,vtpm.yaml

@@ -33,13 +33,13 @@ properties:
   reg:
     maxItems: 1
 
-  'ibm,#dma-address-cells':
+  ibm,#dma-address-cells:
     description:
       number of cells that are used to encode the physical address field of
       dma-window properties
     $ref: /schemas/types.yaml#/definitions/uint32-array
 
-  'ibm,#dma-size-cells':
+  ibm,#dma-size-cells:
     description:
       number of cells that are used to encode the size field of
       dma-window properties