Merge tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "core:
   - Add support for enable attributes to hwmon core
   - Add intrusion templates

  pmbus:
   - Support for Infineon Multi-phase xdpe122 family controllers
   - Support for Intel IMVP9 and AMD 6.25mV modes
   - Support for vid mode detection per page bases
   - Detect if chip is write protected
   - Support for MAX20730, MAX20734, MAX20743, MAX20796, UCD90320,
     TPS53688
   - Various improvements to ibm-cffps driver

  k10temp:
   - Support for additional temperature sensors as well as voltage and
     current telemetry for Zen CPUs

  w83627ehf:
   - Remove support for NCT6775, NCT6776 (they have their own driver)

  New drivers:
   - ADM1177
   - MAX31730
   - Driver for disk and solid state drives with temperature sensors

  Other:
   - pwm-fan: stop fan on shutdown"

* tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (35 commits)
  hwmon: (k10temp) Display up to eight sets of CCD temperatures
  hwmon: (k10temp) Add debugfs support
  hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
  hwmon: (k10temp) Show core and SoC current and voltages on Ryzen CPUs
  hwmon: (k10temp) Report temperatures per CPU die
  hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
  hwmon: (k10temp) Use bitops
  hwmon: (pwm-fan) stop fan on shutdown
  MAINTAINERS: add entry for ADM1177 driver
  dt-binding: hwmon: Add documentation for ADM1177
  hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
  docs: hwmon: Include 'xdpe12284.rst' into docs
  hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
  hwmon: (pmbus/tps53679) Extend device list supported by driver
  hwmon: (pmbus/core) Add support for Intel IMVP9 and AMD 6.25mV modes
  hwmon: (pmbus/core) Add support for vid mode detection per page bases
  hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
  hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
  hwmon: Driver for disk and solid state drives with temperature sensors
  hwmon: (pmbus/ibm-cffps) Fix the LED behavior when turned off
  ...

Author: torvalds

Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml

@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/adi,adm1177.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor
+
+maintainers:
+  - Michael Hennerich <michael.hennerich@analog.com>
+  - Beniamin Bia <beniamin.bia@analog.com>
+
+description: |
+  Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor
+  https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,adm1177
+
+  reg:
+    maxItems: 1
+
+  avcc-supply:
+    description:
+      Phandle to the Avcc power supply
+
+  shunt-resistor-micro-ohms:
+    description:
+      The value of curent sense resistor in microohms. If not provided,
+      the current reading and overcurrent alert is disabled.
+
+  adi,shutdown-threshold-microamp:
+    description:
+      Specifies the current level at which an over current alert occurs.
+      If not provided, the overcurrent alert is configured to max ADC range
+      based on shunt-resistor-micro-ohms.
+
+  adi,vrange-high-enable:
+    description:
+      Specifies which internal voltage divider to be used. A 1 selects
+      a 7:2 voltage divider while a 0 selects a 14:1 voltage divider.
+    type: boolean
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pwmon@5a {
+                compatible = "adi,adm1177";
+                reg = <0x5a>;
+                shunt-resistor-micro-ohms = <50000>; /* 50 mOhm */
+                adi,shutdown-threshold-microamp = <1059000>; /* 1.059 A */
+                adi,vrange-high-enable;
+        };
+    };
+...

Documentation/devicetree/bindings/hwmon/pmbus/ti,ucd90320.yaml

@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/hwmon/pmbus/ti,ucd90320.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: UCD90320 power sequencer
+
+maintainers:
+  - Jim Wright <wrightj@linux.vnet.ibm.com>
+
+description: |
+  The UCD90320 is a 32-rail PMBus/I2C addressable power-supply sequencer and
+  monitor. The 24 integrated ADC channels (AMONx) monitor the power supply
+  voltage, current, and temperature. Of the 84 GPIO pins, 8 can be used as
+  digital monitors (DMONx), 32 to enable the power supply (ENx), 24 for
+  margining (MARx), 16 for logical GPO, and 32 GPIs for cascading, and system
+  function.
+
+  http://focus.ti.com/lit/ds/symlink/ucd90320.pdf
+
+properties:
+  compatible:
+    enum:
+      - ti,ucd90320
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ucd90320@11 {
+            compatible = "ti,ucd90320";
+            reg = <0x11>;
+        };
+    };

Documentation/hwmon/adm1177.rst

@@ -0,0 +1,36 @@
+Kernel driver adm1177
+=====================
+
+Supported chips:
+  * Analog Devices ADM1177
+    Prefix: 'adm1177'
+    Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
+
+Author: Beniamin Bia <beniamin.bia@analog.com>
+
+
+Description
+-----------
+
+This driver supports hardware monitoring for Analog Devices ADM1177
+Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Current maxim attribute
+is read-write, all other attributes are read-only.
+
+in0_input		Measured voltage in microvolts.
+
+curr1_input		Measured current in microamperes.
+curr1_max_alarm		Overcurrent alarm in microamperes.

Documentation/hwmon/drivetemp.rst

@@ -0,0 +1,52 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver drivetemp
+=======================
+
+
+References
+----------
+
+ANS T13/1699-D
+Information technology - AT Attachment 8 - ATA/ATAPI Command Set (ATA8-ACS)
+
+ANS Project T10/BSR INCITS 513
+Information technology - SCSI Primary Commands - 4 (SPC-4)
+
+ANS Project INCITS 557
+Information technology - SCSI / ATA Translation - 5 (SAT-5)
+
+
+Description
+-----------
+
+This driver supports reporting the temperature of disk and solid state
+drives with temperature sensors.
+
+If supported, it uses the ATA SCT Command Transport feature to read
+the current drive temperature and, if available, temperature limits
+as well as historic minimum and maximum temperatures. If SCT Command
+Transport is not supported, the driver uses SMART attributes to read
+the drive temperature.
+
+
+Sysfs entries
+-------------
+
+Only the temp1_input attribute is always available. Other attributes are
+available only if reported by the drive. All temperatures are reported in
+milli-degrees Celsius.
+
+=======================	=====================================================
+temp1_input		Current drive temperature
+temp1_lcrit		Minimum temperature limit. Operating the device below
+			this temperature may cause physical damage to the
+			device.
+temp1_min		Minimum recommended continuous operating limit
+temp1_max		Maximum recommended continuous operating temperature
+temp1_crit		Maximum temperature limit. Operating the device above
+			this temperature may cause physical damage to the
+			device.
+temp1_lowest		Minimum temperature seen this power cycle
+temp1_highest		Maximum temperature seen this power cycle
+=======================	=====================================================

Documentation/hwmon/index.rst

@@ -29,6 +29,7 @@ Hardware Monitoring Kernel Drivers
    adm1025
    adm1026
    adm1031
+   adm1177
    adm1275
    adm9240
    ads7828
@@ -47,6 +48,7 @@ Hardware Monitoring Kernel Drivers
    da9055
    dell-smm-hwmon
    dme1737
+   drivetemp
    ds1621
    ds620
    emc1403
@@ -106,8 +108,10 @@ Hardware Monitoring Kernel Drivers
    max1619
    max1668
    max197
+   max20730
    max20751
    max31722
+   max31730
    max31785
    max31790
    max34440
@@ -177,6 +181,7 @@ Hardware Monitoring Kernel Drivers
    wm831x
    wm8350
    xgene-hwmon
+   xdpe12284
    zl6100
 
 .. only::  subproject and html

Documentation/hwmon/max20730.rst

@@ -0,0 +1,74 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+Kernel driver max20730
+======================
+
+Supported chips:
+
+  * Maxim MAX20730
+
+    Prefix: 'max20730'
+
+    Addresses scanned: -
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20730.pdf
+
+  * Maxim MAX20734
+
+    Prefix: 'max20734'
+
+    Addresses scanned: -
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20734.pdf
+
+  * Maxim MAX20743
+
+    Prefix: 'max20743'
+
+    Addresses scanned: -
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20743.pdf
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+
+Description
+-----------
+
+This driver implements support for Maxim MAX20730, MAX20734, and MAX20743
+Integrated, Step-Down Switching Regulators with PMBus support.
+
+The driver is a client driver to the core PMBus driver.
+Please see Documentation/hwmon/pmbus.rst for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
+details.
+
+
+Sysfs entries
+-------------
+
+=================== ===== =======================================================
+curr1_crit          RW/RO Critical output current. Please see datasheet for
+                          supported limits. Read-only if the chip is
+                          write protected; read-write otherwise.
+curr1_crit_alarm    RO    Output current critical alarm
+curr1_input         RO    Output current
+curr1_label         RO    'iout1'
+in1_alarm           RO    Input voltage alarm
+in1_input           RO    Input voltage
+in1_label           RO    'vin'
+in2_alarm           RO    Output voltage alarm
+in2_input           RO    Output voltage
+in2_label           RO    'vout1'
+temp1_crit          RW/RO Critical temeperature. Supported values are 130 or 150
+                          degrees C. Read-only if the chip is write protected;
+                          read-write otherwise.
+temp1_crit_alarm    RO    Temperature critical alarm
+temp1_input         RO    Chip temperature
+=================== ===== =======================================================

Documentation/hwmon/max31730.rst

@@ -0,0 +1,44 @@
+Kernel driver max31790
+======================
+
+Supported chips:
+
+  * Maxim MAX31730
+
+    Prefix: 'max31730'
+
+    Addresses scanned: 0x1c, 0x1d, 0x1e, 0x1f, 0x4c, 0x4d, 0x4e, 0x4f
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX31730.pdf
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+
+Description
+-----------
+
+This driver implements support for Maxim MAX31730.
+
+The MAX31730 temperature sensor monitors its own temperature and the
+temperatures of three external diode-connected transistors. The operating
+supply voltage is from 3.0V to 3.6V. Resistance cancellation compensates
+for high series resistance in circuit-board traces and the external thermal
+diode, while beta compensation corrects for temperature-measurement
+errors due to low-beta sensing transistors.
+
+
+Sysfs entries
+-------------
+
+=================== == =======================================================
+temp[1-4]_enable    RW Temperature enable/disable
+                       Set to 0 to enable channel, 0 to disable
+temp[1-4]_input     RO Temperature input
+temp[2-4]_fault     RO Fault indicator for remote channels
+temp[1-4]_max       RW Maximum temperature
+temp[1-4]_max_alarm RW Maximum temperature alarm
+temp[1-4]_min       RW Minimum temperature. Common for all channels.
+                       Only temp1_min is writeable.
+temp[1-4]_min_alarm RO Minimum temperature alarm
+temp[2-4]_offset    RW Temperature offset for remote channels
+=================== == =======================================================

Documentation/hwmon/pmbus.rst

@@ -63,6 +63,16 @@ Supported chips:
 
 	http://www.ti.com/lit/gpn/tps544c25
 
+  * Maxim MAX20796
+
+    Prefix: 'max20796'
+
+    Addresses scanned: -
+
+    Datasheet:
+
+	Not published
+
   * Generic PMBus devices
 
     Prefix: 'pmbus'