Merge tag 'ata-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux

Pull ata updates from Niklas Cassel:

 - Fix an incorrect link_power_management_policy sysfs attribute value.

   We were previously using the same attribute value for two different
   LPM policies (me)

 - Add a ASMedia ASM1166 quirk.

   The SATA host controller always reports that it has 32 ports, even
   though it only has six ports. Add a quirk that overrides the value
   reported by the controller (Conrad)

 - Add a ASMedia ASM1061 quirk.

   The SATA host controller completely ignores the upper 21 bits of the
   DMA address. This causes IOMMU error events when a (valid) DMA
   address actually has any of the upper 21 bits set. Add a quirk that
   limits the dma_mask to 43-bits (Lennert)

* tag 'ata-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
  ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers
  ahci: asm1166: correct count of reported ports
  ata: libata-sata: improve sysfs description for ATA_LPM_UNKNOWN

Author: torvalds

drivers/ata/ahci.c

@@ -48,6 +48,7 @@ enum {
 enum board_ids {
 	/* board IDs by feature in alphabetical order */
 	board_ahci,
+	board_ahci_43bit_dma,
 	board_ahci_ign_iferr,
 	board_ahci_low_power,
 	board_ahci_no_debounce_delay,
@@ -128,6 +129,13 @@ static const struct ata_port_info ahci_port_info[] = {
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_ops,
 	},
+	[board_ahci_43bit_dma] = {
+		AHCI_HFLAGS	(AHCI_HFLAG_43BIT_ONLY),
+		.flags		= AHCI_FLAG_COMMON,
+		.pio_mask	= ATA_PIO4,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &ahci_ops,
+	},
 	[board_ahci_ign_iferr] = {
 		AHCI_HFLAGS	(AHCI_HFLAG_IGN_IRQ_IF_ERR),
 		.flags		= AHCI_FLAG_COMMON,
@@ -597,11 +605,11 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(PROMISE, 0x3f20), board_ahci },	/* PDC42819 */
 	{ PCI_VDEVICE(PROMISE, 0x3781), board_ahci },   /* FastTrak TX8660 ahci-mode */
 
-	/* Asmedia */
+	/* ASMedia */
 	{ PCI_VDEVICE(ASMEDIA, 0x0601), board_ahci },	/* ASM1060 */
 	{ PCI_VDEVICE(ASMEDIA, 0x0602), board_ahci },	/* ASM1060 */
-	{ PCI_VDEVICE(ASMEDIA, 0x0611), board_ahci },	/* ASM1061 */
-	{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci },	/* ASM1062 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0611), board_ahci_43bit_dma },	/* ASM1061 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci_43bit_dma },	/* ASM1061/1062 */
 	{ PCI_VDEVICE(ASMEDIA, 0x0621), board_ahci },   /* ASM1061R */
 	{ PCI_VDEVICE(ASMEDIA, 0x0622), board_ahci },   /* ASM1062R */
 	{ PCI_VDEVICE(ASMEDIA, 0x0624), board_ahci },   /* ASM1062+JMB575 */
@@ -663,6 +671,11 @@ MODULE_PARM_DESC(mobile_lpm_policy, "Default LPM policy for mobile chipsets");
 static void ahci_pci_save_initial_config(struct pci_dev *pdev,
 					 struct ahci_host_priv *hpriv)
 {
+	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA && pdev->device == 0x1166) {
+		dev_info(&pdev->dev, "ASM1166 has only six ports\n");
+		hpriv->saved_port_map = 0x3f;
+	}
+
 	if (pdev->vendor == PCI_VENDOR_ID_JMICRON && pdev->device == 0x2361) {
 		dev_info(&pdev->dev, "JMB361 has only one port\n");
 		hpriv->saved_port_map = 1;
@@ -949,11 +962,20 @@ static int ahci_pci_device_resume(struct device *dev)
 
 #endif /* CONFIG_PM */
 
-static int ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
+static int ahci_configure_dma_masks(struct pci_dev *pdev,
+				    struct ahci_host_priv *hpriv)
 {
-	const int dma_bits = using_dac ? 64 : 32;
+	int dma_bits;
 	int rc;
 
+	if (hpriv->cap & HOST_CAP_64) {
+		dma_bits = 64;
+		if (hpriv->flags & AHCI_HFLAG_43BIT_ONLY)
+			dma_bits = 43;
+	} else {
+		dma_bits = 32;
+	}
+
 	/*
 	 * If the device fixup already set the dma_mask to some non-standard
 	 * value, don't extend it here. This happens on STA2X11, for example.
@@ -1926,7 +1948,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	ahci_gtf_filter_workaround(host);
 
 	/* initialize adapter */
-	rc = ahci_configure_dma_masks(pdev, hpriv->cap & HOST_CAP_64);
+	rc = ahci_configure_dma_masks(pdev, hpriv);
 	if (rc)
 		return rc;
 

drivers/ata/ahci.h

@@ -247,6 +247,7 @@ enum {
 	AHCI_HFLAG_SUSPEND_PHYS		= BIT(26), /* handle PHYs during
 						      suspend/resume */
 	AHCI_HFLAG_NO_SXS		= BIT(28), /* SXS not supported */
+	AHCI_HFLAG_43BIT_ONLY		= BIT(29), /* 43bit DMA addr limit */
 
 	/* ap->flags bits */
 

drivers/ata/libata-sata.c

@@ -784,7 +784,7 @@ bool sata_lpm_ignore_phy_events(struct ata_link *link)
 EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
 
 static const char *ata_lpm_policy_names[] = {
-	[ATA_LPM_UNKNOWN]		= "max_performance",
+	[ATA_LPM_UNKNOWN]		= "keep_firmware_settings",
 	[ATA_LPM_MAX_POWER]		= "max_performance",
 	[ATA_LPM_MED_POWER]		= "medium_power",
 	[ATA_LPM_MED_POWER_WITH_DIPM]	= "med_power_with_dipm",

include/linux/libata.h

@@ -471,7 +471,7 @@ enum ata_completion_errors {
 
 /*
  * Link power management policy: If you alter this, you also need to
- * alter libata-scsi.c (for the ascii descriptions)
+ * alter libata-sata.c (for the ascii descriptions)
  */
 enum ata_lpm_policy {
 	ATA_LPM_UNKNOWN,