ARM: dts: Fix erroneous ADS touchscreen polarities

Several device tree files get the polarity of the pendown-gpios
wrong: this signal is active low. Fix up all incorrect flags, so
that operating systems can rely on the flag being correctly set.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230510105156.1134320-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Author: Linus Walleij

arch/arm/boot/dts/am57xx-cl-som-am57x.dts

@@ -527,7 +527,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <31 0>;
-		pendown-gpio = <&gpio1 31 0>;
+		pendown-gpio = <&gpio1 31 GPIO_ACTIVE_LOW>;
 
 
 		ti,x-min = /bits/ 16 <0x0>;

arch/arm/boot/dts/at91sam9261ek.dts

@@ -156,7 +156,7 @@
 					compatible = "ti,ads7843";
 					interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>;
 					spi-max-frequency = <3000000>;
-					pendown-gpio = <&pioC 2 GPIO_ACTIVE_HIGH>;
+					pendown-gpio = <&pioC 2 GPIO_ACTIVE_LOW>;
 
 					ti,x-min = /bits/ 16 <150>;
 					ti,x-max = /bits/ 16 <3830>;

arch/arm/boot/dts/imx7d-pico-hobbit.dts

@@ -64,7 +64,7 @@
 		interrupt-parent = <&gpio2>;
 		interrupts = <7 0>;
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio2 7 0>;
+		pendown-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_3p3v>;
 		ti,x-min = /bits/ 16 <0>;
 		ti,x-max = /bits/ 16 <4095>;

arch/arm/boot/dts/imx7d-sdb.dts

@@ -205,7 +205,7 @@
 		pinctrl-0 = <&pinctrl_tsc2046_pendown>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
-		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;
 		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -227,7 +227,7 @@
 
 		interrupt-parent = <&gpio2>;
 		interrupts = <25 0>;		/* gpio_57 */
-		pendown-gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;

arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi

@@ -54,7 +54,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <27 0>;		/* gpio_27 */
-		pendown-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -311,7 +311,7 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <8 0>;   /* boot6 / gpio_8 */
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_vcc3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tsc2048_pins>;

arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi

@@ -149,7 +149,7 @@
 
 		interrupt-parent = <&gpio4>;
 		interrupts = <18 0>;			/* gpio_114 */
-		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;

arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi

@@ -160,7 +160,7 @@
 
 		interrupt-parent = <&gpio4>;
 		interrupts = <18 0>;			/* gpio_114 */
-		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;

arch/arm/boot/dts/omap3-pandora-common.dtsi

@@ -651,7 +651,7 @@
 		pinctrl-0 = <&penirq_pins>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <30 IRQ_TYPE_NONE>;	/* GPIO_94 */
-		pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio3 30 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&vaux4>;
 
 		ti,x-min = /bits/ 16 <0>;