spi: sun6i: fix RX data corruption in DMA mode

Merge series from Tobias Schramm <t.schramm@manjaro.org>:

This set of patches fixes two bugs in the sun6i SPI driver that result in
corruption of received data in DMA RX mode.

The first bug seems to be related to an incompatibility of the SPI RX FIFO
with wider than single byte read accesses during SPI transfers. I'm not
sure if this bug affects all types of SPI controllers found in Allwinner
SoCs supported by this driver. However reducing the access width should
always be safe. I've tested this change on a V3s SoC. Further testing to
narrow down the set of affected SoCs in the future would be welcome.

The second bug is a race between SPI RX DMA and FIFO drain logic for
interrupt-based SPI operation. This bug affects all SPI controllers
supported by this driver. Once again this change has been tested on the
Allwinner V3s SoC.

Author: broonie

.mailmap

@@ -538,6 +538,8 @@ Shuah Khan <shuah@kernel.org> <shuah.kh@samsung.com>
 Sibi Sankar <quic_sibis@quicinc.com> <sibis@codeaurora.org>
 Sid Manning <quic_sidneym@quicinc.com> <sidneym@codeaurora.org>
 Simon Arlott <simon@octiron.net> <simon@fire.lp0.eu>
+Simon Horman <horms@kernel.org> <simon.horman@corigine.com>
+Simon Horman <horms@kernel.org> <simon.horman@netronome.com>
 Simon Kelley <simon@thekelleys.org.uk>
 Sricharan Ramabadhran <quic_srichara@quicinc.com> <sricharan@codeaurora.org>
 Srinivas Ramana <quic_sramana@quicinc.com> <sramana@codeaurora.org>

Documentation/ABI/testing/sysfs-class-led-trigger-netdev

@@ -13,7 +13,7 @@ Description:
 		Specifies the duration of the LED blink in milliseconds.
 		Defaults to 50 ms.
 
-		With hw_control ON, the interval value MUST be set to the
+		When offloaded is true, the interval value MUST be set to the
 		default value and cannot be changed.
 		Trying to set any value in this specific mode will return
 		an EINVAL error.
@@ -44,8 +44,8 @@ Description:
 		If set to 1, the LED will blink for the milliseconds specified
 		in interval to signal transmission.
 
-		With hw_control ON, the blink interval is controlled by hardware
-		and won't reflect the value set in interval.
+		When offloaded is true, the blink interval is controlled by
+		hardware and won't reflect the value set in interval.
 
 What:		/sys/class/leds/<led>/rx
 Date:		Dec 2017
@@ -59,21 +59,21 @@ Description:
 		If set to 1, the LED will blink for the milliseconds specified
 		in interval to signal reception.
 
-		With hw_control ON, the blink interval is controlled by hardware
-		and won't reflect the value set in interval.
+		When offloaded is true, the blink interval is controlled by
+		hardware and won't reflect the value set in interval.
 
-What:		/sys/class/leds/<led>/hw_control
+What:		/sys/class/leds/<led>/offloaded
 Date:		Jun 2023
 KernelVersion:	6.5
 Contact:	linux-leds@vger.kernel.org
 Description:
-		Communicate whether the LED trigger modes are driven by hardware
-		or software fallback is used.
+		Communicate whether the LED trigger modes are offloaded to
+		hardware or whether software fallback is used.
 
 		If 0, the LED is using software fallback to blink.
 
-		If 1, the LED is using hardware control to blink and signal the
-		requested modes.
+		If 1, the LED blinking in requested mode is offloaded to
+		hardware.
 
 What:		/sys/class/leds/<led>/link_10
 Date:		Jun 2023

Documentation/admin-guide/hw-vuln/srso.rst

@@ -141,8 +141,8 @@ sequence.
 To ensure the safety of this mitigation, the kernel must ensure that the
 safe return sequence is itself free from attacker interference.  In Zen3
 and Zen4, this is accomplished by creating a BTB alias between the
-untraining function srso_untrain_ret_alias() and the safe return
-function srso_safe_ret_alias() which results in evicting a potentially
+untraining function srso_alias_untrain_ret() and the safe return
+function srso_alias_safe_ret() which results in evicting a potentially
 poisoned BTB entry and using that safe one for all function returns.
 
 In older Zen1 and Zen2, this is accomplished using a reinterpretation

Documentation/devicetree/bindings/pinctrl/qcom,sa8775p-tlmm.yaml

@@ -87,7 +87,7 @@ $defs:
                 emac0_mdc, emac0_mdio, emac0_ptp_aux, emac0_ptp_pps, emac1_mcg0,
                 emac1_mcg1, emac1_mcg2, emac1_mcg3, emac1_mdc, emac1_mdio,
                 emac1_ptp_aux, emac1_ptp_pps, gcc_gp1, gcc_gp2, gcc_gp3,
-                gcc_gp4, gcc_gp5, hs0_mi2s, hs1_mi2s, hs2_mi2s, ibi_i3c,
+                gcc_gp4, gcc_gp5, gpio, hs0_mi2s, hs1_mi2s, hs2_mi2s, ibi_i3c,
                 jitter_bist, mdp0_vsync0, mdp0_vsync1, mdp0_vsync2, mdp0_vsync3,
                 mdp0_vsync4, mdp0_vsync5, mdp0_vsync6, mdp0_vsync7, mdp0_vsync8,
                 mdp1_vsync0, mdp1_vsync1, mdp1_vsync2, mdp1_vsync3, mdp1_vsync4,

Documentation/i2c/writing-clients.rst

@@ -46,7 +46,7 @@ driver model device node, and its I2C address.
 	},
 
 	.id_table	= foo_idtable,
-	.probe_new	= foo_probe,
+	.probe		= foo_probe,
 	.remove		= foo_remove,
 	/* if device autodetection is needed: */
 	.class		= I2C_CLASS_SOMETHING,

Documentation/networking/nf_conntrack-sysctl.rst

@@ -178,10 +178,10 @@ nf_conntrack_sctp_timeout_established - INTEGER (seconds)
 	Default is set to (hb_interval * path_max_retrans + rto_max)
 
 nf_conntrack_sctp_timeout_shutdown_sent - INTEGER (seconds)
-	default 0.3
+	default 3
 
 nf_conntrack_sctp_timeout_shutdown_recd - INTEGER (seconds)
-	default 0.3
+	default 3
 
 nf_conntrack_sctp_timeout_shutdown_ack_sent - INTEGER (seconds)
 	default 3

MAINTAINERS

@@ -8816,6 +8816,7 @@ R:	Michael Walle <michael@walle.cc>
 S:	Maintained
 F:	drivers/gpio/gpio-regmap.c
 F:	include/linux/gpio/regmap.h
+K:	(devm_)?gpio_regmap_(un)?register
 
 GPIO SUBSYSTEM
 M:	Linus Walleij <linus.walleij@linaro.org>
@@ -14816,6 +14817,16 @@ F:	net/netfilter/xt_CONNSECMARK.c
 F:	net/netfilter/xt_SECMARK.c
 F:	net/netlabel/
 
+NETWORKING [MACSEC]
+M:	Sabrina Dubroca <sd@queasysnail.net>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/macsec.c
+F:	include/net/macsec.h
+F:	include/uapi/linux/if_macsec.h
+K:	macsec
+K:	\bmdo_
+
 NETWORKING [MPTCP]
 M:	Matthieu Baerts <matthieu.baerts@tessares.net>
 M:	Mat Martineau <martineau@kernel.org>
@@ -19237,13 +19248,6 @@ F:	Documentation/devicetree/bindings/serial/serial.yaml
 F:	drivers/tty/serdev/
 F:	include/linux/serdev.h
 
-SERIAL DRIVERS
-M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-L:	linux-serial@vger.kernel.org
-S:	Maintained
-F:	Documentation/devicetree/bindings/serial/
-F:	drivers/tty/serial/
-
 SERIAL IR RECEIVER
 M:	Sean Young <sean@mess.org>
 L:	linux-media@vger.kernel.org
@@ -21072,6 +21076,39 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/sound/davinci-mcasp-audio.yaml
 F:	sound/soc/ti/
 
+TEXAS INSTRUMENTS AUDIO (ASoC/HDA) DRIVERS
+M:	Shenghao Ding <shenghao-ding@ti.com>
+M:	Kevin Lu <kevin-lu@ti.com>
+M:	Baojun Xu <x1077012@ti.com>
+L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
+S:	Maintained
+F:	Documentation/devicetree/bindings/sound/tas2552.txt
+F:	Documentation/devicetree/bindings/sound/tas2562.yaml
+F:	Documentation/devicetree/bindings/sound/tas2770.yaml
+F:	Documentation/devicetree/bindings/sound/tas27xx.yaml
+F:	Documentation/devicetree/bindings/sound/ti,pcm1681.txt
+F:	Documentation/devicetree/bindings/sound/ti,pcm3168a.yaml
+F:	Documentation/devicetree/bindings/sound/ti,tlv320*.yaml
+F:	Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
+F:	Documentation/devicetree/bindings/sound/tlv320aic31xx.txt
+F:	Documentation/devicetree/bindings/sound/tpa6130a2.txt
+F:	include/sound/tas2*.h
+F:	include/sound/tlv320*.h
+F:	include/sound/tpa6130a2-plat.h
+F:	sound/pci/hda/tas2781_hda_i2c.c
+F:	sound/soc/codecs/pcm1681.c
+F:	sound/soc/codecs/pcm1789*.*
+F:	sound/soc/codecs/pcm179x*.*
+F:	sound/soc/codecs/pcm186x*.*
+F:	sound/soc/codecs/pcm3008.*
+F:	sound/soc/codecs/pcm3060*.*
+F:	sound/soc/codecs/pcm3168a*.*
+F:	sound/soc/codecs/pcm5102a.c
+F:	sound/soc/codecs/pcm512x*.*
+F:	sound/soc/codecs/tas2*.*
+F:	sound/soc/codecs/tlv320*.*
+F:	sound/soc/codecs/tpa6130a2.*
+
 TEXAS INSTRUMENTS DMA DRIVERS
 M:	Peter Ujfalusi <peter.ujfalusi@gmail.com>
 L:	dmaengine@vger.kernel.org
@@ -21648,20 +21685,16 @@ W:	https://github.com/srcres258/linux-doc
 T:	git git://github.com/srcres258/linux-doc.git doc-zh-tw
 F:	Documentation/translations/zh_TW/
 
-TTY LAYER
+TTY LAYER AND SERIAL DRIVERS
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 M:	Jiri Slaby <jirislaby@kernel.org>
 L:	linux-kernel@vger.kernel.org
 L:	linux-serial@vger.kernel.org
 S:	Supported
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
+F:	Documentation/devicetree/bindings/serial/
 F:	Documentation/driver-api/serial/
 F:	drivers/tty/
-F:	drivers/tty/serial/serial_base.h
-F:	drivers/tty/serial/serial_base_bus.c
-F:	drivers/tty/serial/serial_core.c
-F:	drivers/tty/serial/serial_ctrl.c
-F:	drivers/tty/serial/serial_port.c
 F:	include/linux/selection.h
 F:	include/linux/serial.h
 F:	include/linux/serial_core.h
@@ -22488,7 +22521,6 @@ L:	virtualization@lists.linux-foundation.org
 S:	Maintained
 F:	drivers/block/virtio_blk.c
 F:	drivers/scsi/virtio_scsi.c
-F:	drivers/vhost/scsi.c
 F:	include/uapi/linux/virtio_blk.h
 F:	include/uapi/linux/virtio_scsi.h
 
@@ -22587,6 +22619,16 @@ F:	include/linux/vhost_iotlb.h
 F:	include/uapi/linux/vhost.h
 F:	kernel/vhost_task.c
 
+VIRTIO HOST (VHOST-SCSI)
+M:	"Michael S. Tsirkin" <mst@redhat.com>
+M:	Jason Wang <jasowang@redhat.com>
+M:	Mike Christie <michael.christie@oracle.com>
+R:	Paolo Bonzini <pbonzini@redhat.com>
+R:	Stefan Hajnoczi <stefanha@redhat.com>
+L:	virtualization@lists.linux-foundation.org
+S:	Maintained
+F:	drivers/vhost/scsi.c
+
 VIRTIO I2C DRIVER
 M:	Conghui Chen <conghui.chen@intel.com>
 M:	Viresh Kumar <viresh.kumar@linaro.org>

Makefile

@@ -2,7 +2,7 @@
 VERSION = 6
 PATCHLEVEL = 5
 SUBLEVEL = 0
-EXTRAVERSION = -rc6
+EXTRAVERSION =
 NAME = Hurr durr I'ma ninja sloth
 
 # *DOCUMENTATION*

arch/arm/boot/dts/arm/integratorap.dts

@@ -158,7 +158,7 @@
 		valid-mask = <0x003fffff>;
 	};
 
-	pci: pciv3@62000000 {
+	pci: pci@62000000 {
 		compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
 		device_type = "pci";
 		#interrupt-cells = <1>;

arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi

@@ -182,7 +182,7 @@
 		pinctrl-0 = <&pinctrl_rtc_int>;
 		reg = <0x68>;
 		interrupt-parent = <&gpio7>;
-		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		status = "disabled";
 	};
 };