Merge tag 'mvebu-dt64-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt

mvebu dt64 for 5.19 (part 1)

Update sdhci node names to match schema on all mvebu dt64 dtsi files

Armada 3720:
  uDPU board:
   - correct temperature sensors
   - update partition table

  espressobin-ultra board:
   - enable front USB3 port
   - add PHY and switch reset pins
   - fix SPI-NOR config

* tag 'mvebu-dt64-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
  arm64: dts: marvell: Update sdhci node names to match schema
  arm64: dts: marvell: espressobin-ultra: enable front USB3 port
  arm64: dts: marvell: espressobin-ultra: add PHY and switch reset pins
  arm64: dts: marvell: espressobin-ultra: fix SPI-NOR config
  arm64: dts: uDPU: correct temperature sensors
  arm64: dts: uDPU: update partition table

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Author: arndb

arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts

@@ -71,10 +71,6 @@
 
 &spi0 {
 	flash@0 {
-		spi-max-frequency = <108000000>;
-		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
-
 		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
@@ -112,18 +108,21 @@
 
 &usb3 {
 	usb-phy = <&usb3_phy>;
-	status = "disabled";
 };
 
 &mdio {
 	extphy: ethernet-phy@1 {
 		reg = <1>;
+
+		reset-gpios = <&gpionb 2 GPIO_ACTIVE_LOW>;
 	};
 };
 
 &switch0 {
 	reg = <3>;
 
+	reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;
+
 	ports {
 		switch0port1: port@1 {
 			reg = <1>;

arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts

@@ -108,10 +108,15 @@
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			/* only bootloader is located on the SPI */
+
 			partition@0 {
-				label = "uboot";
-				reg = <0 0x400000>;
+				label = "firmware";
+				reg = <0x0 0x180000>;
+			};
+
+			partition@180000 {
+				label = "u-boot-env";
+				reg = <0x180000 0x10000>;
 			};
 		};
 	};
@@ -148,15 +153,15 @@
 	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 
-	lm75@48 {
+	nct375@48 {
 		status = "okay";
-		compatible = "lm75";
+		compatible = "ti,tmp75c";
 		reg = <0x48>;
 	};
 
-	lm75@49 {
+	nct375@49 {
 		status = "okay";
-		compatible = "lm75";
+		compatible = "ti,tmp75c";
 		reg = <0x49>;
 	};
 };

arch/arm64/boot/dts/marvell/armada-37xx.dtsi

@@ -444,7 +444,7 @@
 				#mbox-cells = <1>;
 			};
 
-			sdhci1: sdhci@d0000 {
+			sdhci1: mmc@d0000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";
 				reg = <0xd0000 0x300>,
@@ -455,7 +455,7 @@
 				status = "disabled";
 			};
 
-			sdhci0: sdhci@d8000 {
+			sdhci0: mmc@d8000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";
 				reg = <0xd8000 0x300>,

arch/arm64/boot/dts/marvell/armada-ap80x.dtsi

@@ -250,7 +250,7 @@
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			ap_sdhci0: sdhci@6e0000 {
+			ap_sdhci0: mmc@6e0000 {
 				compatible = "marvell,armada-ap806-sdhci";
 				reg = <0x6e0000 0x300>;
 				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;

arch/arm64/boot/dts/marvell/armada-cp11x.dtsi

@@ -493,7 +493,7 @@
 			status = "okay";
 		};
 
-		CP11X_LABEL(sdhci0): sdhci@780000 {
+		CP11X_LABEL(sdhci0): mmc@780000 {
 			compatible = "marvell,armada-cp110-sdhci";
 			reg = <0x780000 0x300>;
 			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;