ata: Fix typos in the comment

Correctly spelled comments make it easier for the reader to understand
the code.

Fix typos:
'multipe' ==> 'multiple',
'Paremeters' ==> 'Parameters',
'recieved' ==> 'received',
'realted' ==> 'related',
'evaulated' ==> 'evaluated',
'programing' ==> 'programming',
'coninue' ==> 'continue'.

Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240927060056.221977-1-yanzhen@vivo.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>

Author: Yan Zhen

drivers/ata/ahci.c

@@ -1676,7 +1676,7 @@ static int ahci_init_msi(struct pci_dev *pdev, unsigned int n_ports,
 	/*
 	 * If number of MSIs is less than number of ports then Sharing Last
 	 * Message mode could be enforced. In this case assume that advantage
-	 * of multipe MSIs is negated and use single MSI mode instead.
+	 * of multiple MSIs is negated and use single MSI mode instead.
 	 */
 	if (n_ports > 1) {
 		nvec = pci_alloc_irq_vectors(pdev, n_ports, INT_MAX,

drivers/ata/ahci_imx.c

@@ -511,7 +511,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
 
 	if (imxpriv->type == AHCI_IMX6Q || imxpriv->type == AHCI_IMX6QP) {
 		/*
-		 * set PHY Paremeters, two steps to configure the GPR13,
+		 * set PHY Parameters, two steps to configure the GPR13,
 		 * one write for rest of parameters, mask of first write
 		 * is 0x07ffffff, and the other one write for setting
 		 * the mpll_clk_en.

drivers/ata/ahci_xgene.c

@@ -534,7 +534,7 @@ static int xgene_ahci_softreset(struct ata_link *link, unsigned int *class,
 
 /**
  * xgene_ahci_handle_broken_edge_irq - Handle the broken irq.
- * @host: Host that recieved the irq
+ * @host: Host that received the irq
  * @irq_masked: HOST_IRQ_STAT value
  *
  * For hardware with broken edge trigger latch

drivers/ata/libata-acpi.c

@@ -86,7 +86,7 @@ static void ata_acpi_detach_device(struct ata_port *ap, struct ata_device *dev)
  * @dev: ATA device ACPI event occurred (can be NULL)
  * @event: ACPI event which occurred
  *
- * All ACPI bay / device realted events end up in this function.  If
+ * All ACPI bay / device related events end up in this function.  If
  * the event is port-wide @dev is NULL.  If the event is specific to a
  * device, @dev points to it.
  *
@@ -832,7 +832,7 @@ void ata_acpi_on_resume(struct ata_port *ap)
 				dev->flags |= ATA_DFLAG_ACPI_PENDING;
 		}
 	} else {
-		/* SATA _GTF needs to be evaulated after _SDD and
+		/* SATA _GTF needs to be evaluated after _SDD and
 		 * there's no reason to evaluate IDE _GTF early
 		 * without _STM.  Clear cache and schedule _GTF.
 		 */

drivers/ata/pata_it8213.c

@@ -81,7 +81,7 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
 	int control = 0;
 
 	/*
-	 *	See Intel Document 298600-004 for the timing programing rules
+	 *	See Intel Document 298600-004 for the timing programming rules
 	 *	for PIIX/ICH. The 8213 is a clone so very similar
 	 */
 

drivers/ata/pata_octeon_cf.c

@@ -183,7 +183,7 @@ static void octeon_cf_set_piomode(struct ata_port *ap, struct ata_device *dev)
 	reg_tim.s.ale = 0;
 	/* Not used */
 	reg_tim.s.page = 0;
-	/* Time after IORDY to coninue to assert the data */
+	/* Time after IORDY to continue to assert the data */
 	reg_tim.s.wait = 0;
 	/* Time to wait to complete the cycle. */
 	reg_tim.s.pause = pause;

drivers/ata/pata_oldpiix.c

@@ -70,7 +70,7 @@ static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev)
 	int control = 0;
 
 	/*
-	 *	See Intel Document 298600-004 for the timing programing rules
+	 *	See Intel Document 298600-004 for the timing programming rules
 	 *	for PIIX/ICH. Note that the early PIIX does not have the slave
 	 *	timing port at 0x44.
 	 */

drivers/ata/pata_radisys.c

@@ -45,7 +45,7 @@ static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
 	int control = 0;
 
 	/*
-	 *	See Intel Document 298600-004 for the timing programing rules
+	 *	See Intel Document 298600-004 for the timing programming rules
 	 *	for PIIX/ICH. Note that the early PIIX does not have the slave
 	 *	timing port at 0x44. The Radisys is a relative of the PIIX
 	 *	but not the same so be careful.