Merge tag 'gpio-updates-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
 "It's been a relatively calm release cycle and we're actually removing
  more code than we're adding.

  Summary:

   - new driver for the Toshiba Visconti platform

   - rework of interrupt handling in gpio-tegra

   - updates for GPIO selftests: we're now using the character device to
     perform the subsystem checks

   - support for a new rcar variant + some code refactoring

   - refactoring of gpio-ep93xx

   - SPDX License identifier has been updated in the uapi header so that
     userspace programs bundling it can become fully REUSE-compliant

   - improvements to pwm handling in gpio-mvebu

   - support for interrupt handling and power management for gpio-xilinx
     as well as some code refactoring

   - support for a new chip variant in gpio-pca953x

   - removal of drivers: zte xs & intel-mid and removal of leftovers
     from intel-msic

   - impovements to intel drivers pulled from Andy Shevchenko

   - improvements to the gpio-aggregator virtual GPIO driver

   - and several minor tweaks and fixes to code and documentation all
     over the place"

* tag 'gpio-updates-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (71 commits)
  gpio: pcf857x: Fix missing first interrupt
  gpio: ep93xx: refactor base IRQ number
  gpio: ep93xx: refactor ep93xx_gpio_add_bank
  gpio: ep93xx: Fix typo s/hierarchial/hierarchical
  gpio: ep93xx: drop to_irq binding
  gpio: ep93xx: Fix wrong irq numbers in port F
  gpio: uapi: use the preferred SPDX license identifier
  gpio: gpio-xilinx: Add check if width exceeds 32
  gpio: gpio-xilinx: Add support for suspend and resume
  gpio: gpio-xilinx: Add interrupt support
  gpio: gpio-xilinx: Reduce spinlock array to array
  gpio: gpio-xilinx: Simplify with dev_err_probe()
  gpio: msic: Drop driver from Makefile
  gpio: wcove: Split out to_ireg() helper and deduplicate the code
  gpio: wcove: Switch to use regmap_set_bits(), regmap_clear_bits()
  gpio: wcove: Get rid of error prone casting in IRQ handler
  gpio: intel-mid: Remove driver for deprecated platform
  gpio: msic: Remove driver for deprecated platform
  gpio: aggregator: Remove trailing comma in terminator entries
  gpio: aggregator: Use compound literal from the header
  ...

Author: torvalds

Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt

@@ -80,6 +80,11 @@ Required properties:
 
 - offset: offset address inside the syscon block
 
+Optional properties:
+
+- marvell,pwm-offset: offset address of PWM duration control registers inside
+  the syscon block
+
 Example:
 ap_syscon: system-controller@6f4000 {
 	compatible = "syscon", "simple-mfd";
@@ -101,6 +106,9 @@ ap_syscon: system-controller@6f4000 {
 		gpio-controller;
 		#gpio-cells = <2>;
 		gpio-ranges = <&ap_pinctrl 0 0 19>;
+		marvell,pwm-offset = <0x10c0>;
+		#pwm-cells = <2>;
+		clocks = <&ap_clk 3>;
 	};
 };
 

Documentation/devicetree/bindings/gpio/gpio-davinci.txt

@@ -7,6 +7,7 @@ Required Properties:
 			"ti,k2g-gpio", "ti,keystone-gpio": for 66AK2G
 			"ti,am654-gpio", "ti,keystone-gpio": for TI K3 AM654
 			"ti,j721e-gpio", "ti,keystone-gpio": for J721E SoCs
+			"ti,am64-gpio", "ti,keystone-gpio": for AM64 SoCs
 
 - reg: Physical base address of the controller and the size of memory mapped
        registers.

Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml

@@ -32,6 +32,7 @@ properties:
       - maxim,max7327
       - nxp,pca6416
       - nxp,pca9505
+      - nxp,pca9506
       - nxp,pca9534
       - nxp,pca9535
       - nxp,pca9536
@@ -70,7 +71,7 @@ properties:
 
   gpio-line-names:
     minItems: 1
-    maxItems: 32
+    maxItems: 40
 
   interrupts:
     maxItems: 1

Documentation/devicetree/bindings/gpio/renesas,rcar-gpio.yaml

@@ -48,6 +48,9 @@ properties:
               - renesas,gpio-r8a77995     # R-Car D3
           - const: renesas,rcar-gen3-gpio # R-Car Gen3 or RZ/G2
 
+      - items:
+          - const: renesas,gpio-r8a779a0  # R-Car V3U
+
   reg:
     maxItems: 1
 

Documentation/devicetree/bindings/gpio/toshiba,gpio-visconti.yaml

@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/toshiba,gpio-visconti.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba Visconti ARM SoCs GPIO controller
+
+maintainers:
+  - Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+
+properties:
+  compatible:
+    items:
+      - const: toshiba,gpio-tmpv7708
+
+  reg:
+    maxItems: 1
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-ranges: true
+
+  gpio-controller: true
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  interrupts:
+    description:
+      interrupt mapping one per GPIO.
+    minItems: 16
+    maxItems: 16
+
+required:
+  - compatible
+  - reg
+  - "#gpio-cells"
+  - gpio-ranges
+  - gpio-controller
+  - interrupt-controller
+  - "#interrupt-cells"
+  - interrupt-parent
+
+additionalProperties: false
+
+examples:
+  - |
+      #include <dt-bindings/interrupt-controller/irq.h>
+      #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+      soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        gpio: gpio@28020000 {
+          compatible = "toshiba,gpio-tmpv7708";
+          reg = <0 0x28020000 0 0x1000>;
+          #gpio-cells = <0x2>;
+          gpio-ranges = <&pmux 0 0 32>;
+          gpio-controller;
+          interrupt-controller;
+          #interrupt-cells = <2>;
+          interrupt-parent = <&gic>;
+        };
+      };
+...

Documentation/devicetree/bindings/gpio/zx296702-gpio.txt

@@ -361,12 +361,13 @@ corresponding chip driver. In that case a significantly improved performance
 can be expected. If simultaneous access is not possible the GPIOs will be
 accessed sequentially.
 
-The functions take three arguments:
+The functions take four arguments:
+
 	* array_size	- the number of array elements
 	* desc_array	- an array of GPIO descriptors
 	* array_info	- optional information obtained from gpiod_get_array()
 	* value_bitmap	- a bitmap to store the GPIOs' values (get) or
-			  a bitmap of values to assign to the GPIOs (set)
+          a bitmap of values to assign to the GPIOs (set)
 
 The descriptor array can be obtained using the gpiod_get_array() function
 or one of its variants. If the group of descriptors returned by that function

Documentation/driver-api/gpio/consumer.rst

@@ -106,11 +106,11 @@ don't. When you need open drain signaling but your hardware doesn't directly
 support it, there's a common idiom you can use to emulate it with any GPIO pin
 that can be used as either an input or an output:
 
- LOW:	gpiod_direction_output(gpio, 0) ... this drives the signal and overrides
-	the pullup.
+ **LOW**: ``gpiod_direction_output(gpio, 0)`` ... this drives the signal and
+ overrides the pullup.
 
- HIGH:	gpiod_direction_input(gpio) ... this turns off the output, so the pullup
-	(or some other device) controls the signal.
+ **HIGH**: ``gpiod_direction_input(gpio)`` ... this turns off the output, so
+ the pullup (or some other device) controls the signal.
 
 The same logic can be applied to emulate open source signaling, by driving the
 high signal and configuring the GPIO as input for low. This open drain/open

Documentation/driver-api/gpio/intro.rst

@@ -2609,10 +2609,12 @@ S:	Supported
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti.git
 F:	Documentation/devicetree/bindings/arm/toshiba.yaml
 F:	Documentation/devicetree/bindings/net/toshiba,visconti-dwmac.yaml
+F:	Documentation/devicetree/bindings/gpio/toshiba,gpio-visconti.yaml
 F:	Documentation/devicetree/bindings/pinctrl/toshiba,tmpv7700-pinctrl.yaml
 F:	Documentation/devicetree/bindings/watchdog/toshiba,visconti-wdt.yaml
 F:	arch/arm64/boot/dts/toshiba/
 F:	drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
+F:	drivers/gpio/gpio-visconti.c
 F:	drivers/pinctrl/visconti/
 F:	drivers/watchdog/visconti_wdt.c
 N:	visconti

MAINTAINERS

@@ -487,11 +487,11 @@ config GPIO_PXA
 	  Say yes here to support the PXA GPIO device
 
 config GPIO_RCAR
-	tristate "Renesas R-Car GPIO"
+	tristate "Renesas R-Car and RZ/G GPIO support"
 	depends on ARCH_RENESAS || COMPILE_TEST
 	select GPIOLIB_IRQCHIP
 	help
-	  Say yes here to support GPIO on Renesas R-Car SoCs.
+	  Say yes here to support GPIO on Renesas R-Car or RZ/G SoCs.
 
 config GPIO_RDA
 	bool "RDA Micro GPIO controller support"
@@ -595,7 +595,7 @@ config GPIO_TB10X
 	select OF_GPIO
 
 config GPIO_TEGRA
-	bool "NVIDIA Tegra GPIO support"
+	tristate "NVIDIA Tegra GPIO support"
 	default ARCH_TEGRA
 	depends on ARCH_TEGRA || COMPILE_TEST
 	depends on OF_GPIO
@@ -648,6 +648,16 @@ config GPIO_VF610
 	help
 	  Say yes here to support Vybrid vf610 GPIOs.
 
+config GPIO_VISCONTI
+	tristate "Toshiba Visconti GPIO support"
+	depends on ARCH_VISCONTI || COMPILE_TEST
+	depends on OF_GPIO
+	select GPIOLIB_IRQCHIP
+	select GPIO_GENERIC
+	select IRQ_DOMAIN_HIERARCHY
+	help
+	  Say yes here to support GPIO on Tohisba Visconti.
+
 config GPIO_VR41XX
 	tristate "NEC VR4100 series General-purpose I/O Uint support"
 	depends on CPU_VR41XX
@@ -670,7 +680,7 @@ config GPIO_WCD934X
 	tristate "Qualcomm Technologies Inc WCD9340/WCD9341 gpio controller driver"
 	depends on MFD_WCD934X && OF_GPIO
 	help
-         This driver is to supprot GPIO block found on the Qualcomm Technologies
+         This driver is to support GPIO block found on the Qualcomm Technologies
 	 Inc WCD9340/WCD9341 Audio Codec.
 
 config GPIO_XGENE
@@ -694,6 +704,8 @@ config GPIO_XGENE_SB
 
 config GPIO_XILINX
 	tristate "Xilinx GPIO support"
+	select GPIOLIB_IRQCHIP
+	depends on OF_GPIO
 	help
 	  Say yes here to support the Xilinx FPGA GPIO device
 
@@ -731,13 +743,6 @@ config GPIO_ZYNQ
 	help
 	  Say yes here to support Xilinx Zynq GPIO controller.
 
-config GPIO_ZX
-	bool "ZTE ZX GPIO support"
-	depends on ARCH_ZX || COMPILE_TEST
-	select GPIOLIB_IRQCHIP
-	help
-	  Say yes here to support the GPIO device on ZTE ZX SoCs.
-
 config GPIO_LOONGSON1
 	tristate "Loongson1 GPIO support"
 	depends on MACH_LOONGSON32
@@ -1623,8 +1628,7 @@ config GPIO_MOCKUP
 	select IRQ_SIM
 	help
 	  This enables GPIO Testing driver, which provides a way to test GPIO
-	  subsystem through sysfs(or char device) and debugfs. GPIO_SYSFS
-	  must be selected for this test.
+	  subsystem through sysfs (or char device) and debugfs.
 	  User could use it through the script in
 	  tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
 	  it.