Merge tag 'thermal-v6.6-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux

Merge ARM and related thermal control updates for 6.6-rc1 from Daniel
Lezcano:

"- Check if the Tegra BPMP supports the trip points in order to set the
   .set_trips callback (Mikko Perttunen)

 - Add the new Loongson-2 thermal sensor along with the DT bindings
   (Yinbo Zhu)

 - Use IS_ERR_OR_NULL helper to replace a double test on the TI bandgap
   sensor (Li Zetao)

 - Remove the call to platform_set_drvdata() as there is no call to
   platform_get_drvdata() in a bunch of drivers where that happens
   (Andrei Coardos)

 - Switch the Mediatek LVTS mode to filtered in order to enable the
   interrupts (Nícolas F. R. A. Prado)

 - Fix Wvoid-pointer-to-enum-cast warning on the Exynos TMU (Krzysztof
   Kozlowski)

 - Remove redundant usage of of_match_ptr() as the driver db8500
   already depends on CONFIG_OF (Ruan Jinjie)

 - Remove redundant dev_err_probe() because the underlying function
   already called it in the Mediatek sensor (Chen Jiahao)

 - Free calibration nvmem after reading it on sun8i (Mark Brown)

 - Remove useless comment in the code on sun8i (Yangtao Li)

 - Make tsens_xxxx_nvmem static to fix sparse warning on QCom tsens (Min-Hua Chen)

 - Remove error message at probe deferral on imx8mm (Ahmad Fatoum)

 - Fix parameter check in lvts_debugfs_init with IS_ERR on Mediatek
   LVTS (Minjie Du)

 - Fix the interrupt routine and configuratoin for the Mediatek LVTS
   (Nícolas F. R. A. Prado)"

* tag 'thermal-v6.6-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (27 commits)
  thermal/drivers/tegra-bpmp: Check if BPMP supports trip points
  thermal: dt-bindings: add loongson-2 thermal
  thermal/drivers/loongson-2: Add thermal management support
  thermal/drivers/ti-soc-thermal: Use helper function IS_ERR_OR_NULL()
  thermal/drivers/generic-adc: Removed unneeded call to platform_set_drvdata()
  thermal/drivers/max77620_thermal: Removed unneeded call to platform_set_drvdata()
  thermal/drivers/mediatek/auxadc_thermal: Removed call to platform_set_drvdata()
  thermal/drivers/sun8i_thermal: Remove unneeded call to platform_set_drvdata()
  thermal/drivers/broadcom/brcstb_thermal: Removed unneeded platform_set_drvdata()
  thermal/drivers/mediatek/lvts_thermal: Make readings valid in filtered mode
  thermal/drivers/k3_bandgap: Remove unneeded call to platform_set_drvdata()
  thermal/drivers/k3_j72xx_bandgap: Removed unneeded call to platform_set_drvdata()
  thermal/drivers/broadcom/sr-thermal: Removed call to platform_set_drvdata()
  thermal/drivers/samsung: Fix Wvoid-pointer-to-enum-cast warning
  thermal/drivers/db8500: Remove redundant of_match_ptr()
  thermal/drivers/mediatek: Clean up redundant dev_err_probe()
  thermal/drivers/sun8i: Free calibration nvmem after reading it
  thermal/drivers/sun8i: Remove unneeded comments
  thermal/drivers/tsens: Make tsens_xxxx_nvmem static
  thermal/drivers/imx8mm: Suppress log message on probe deferral
  ...

Author: rafaeljw

Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml

@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/loongson,ls2k-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Thermal sensors on Loongson-2 SoCs
+
+maintainers:
+  - zhanghongchen <zhanghongchen@loongson.cn>
+  - Yinbo Zhu <zhuyinbo@loongson.cn>
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - loongson,ls2k1000-thermal
+      - items:
+          - enum:
+              - loongson,ls2k2000-thermal
+          - const: loongson,ls2k1000-thermal
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    thermal: thermal-sensor@1fe01500 {
+        compatible = "loongson,ls2k1000-thermal";
+        reg = <0x1fe01500 0x30>;
+        interrupt-parent = <&liointc0>;
+        interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+    };

MAINTAINERS

@@ -12295,6 +12295,14 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/pinctrl/loongson,ls2k-pinctrl.yaml
 F:	drivers/pinctrl/pinctrl-loongson2.c
 
+LOONGSON-2 SOC SERIES THERMAL DRIVER
+M:	zhanghongchen <zhanghongchen@loongson.cn>
+M:	Yinbo Zhu <zhuyinbo@loongson.cn>
+L:	linux-pm@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/thermal/loongson,ls2k-thermal.yaml
+F:	drivers/thermal/loongson2_thermal.c
+
 LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
 M:	Sathya Prakash <sathya.prakash@broadcom.com>
 M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>

drivers/thermal/Kconfig

@@ -510,4 +510,16 @@ config KHADAS_MCU_FAN_THERMAL
 	  If you say yes here you get support for the FAN controlled
 	  by the Microcontroller found on the Khadas VIM boards.
 
+config LOONGSON2_THERMAL
+	tristate "Loongson-2 SoC series thermal driver"
+	depends on LOONGARCH || COMPILE_TEST
+	depends on OF
+	help
+	  Support for Thermal driver found on Loongson-2 SoC series platforms.
+	  The thermal driver realizes get_temp and set_trips function, which
+	  are used to obtain the temperature of the current node and set the
+	  temperature range to trigger the interrupt. When the input temperature
+	  is higher than the high temperature threshold or lower than the low
+	  temperature threshold, the interrupt will occur.
+
 endif

drivers/thermal/Makefile

@@ -63,3 +63,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
 obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
 obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
 obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
+obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o

drivers/thermal/broadcom/brcmstb_thermal.c

@@ -334,7 +334,6 @@ static int brcmstb_thermal_probe(struct platform_device *pdev)
 		return PTR_ERR(priv->tmon_base);
 
 	priv->dev = &pdev->dev;
-	platform_set_drvdata(pdev, priv);
 	of_ops = priv->temp_params->of_ops;
 
 	thermal = devm_thermal_of_zone_register(&pdev->dev, 0, priv,

drivers/thermal/broadcom/sr-thermal.c

@@ -91,7 +91,6 @@ static int sr_thermal_probe(struct platform_device *pdev)
 
 		dev_dbg(dev, "thermal sensor %d registered\n", i);
 	}
-	platform_set_drvdata(pdev, sr_thermal);
 
 	return 0;
 }

drivers/thermal/db8500_thermal.c

@@ -229,7 +229,7 @@ MODULE_DEVICE_TABLE(of, db8500_thermal_match);
 static struct platform_driver db8500_thermal_driver = {
 	.driver = {
 		.name = "db8500-thermal",
-		.of_match_table = of_match_ptr(db8500_thermal_match),
+		.of_match_table = db8500_thermal_match,
 	},
 	.probe = db8500_thermal_probe,
 	.suspend = db8500_thermal_suspend,

drivers/thermal/imx8mm_thermal.c

@@ -178,10 +178,8 @@ static int imx8mm_tmu_probe_set_calib_v1(struct platform_device *pdev,
 	int ret;
 
 	ret = nvmem_cell_read_u32(&pdev->dev, "calib", &ana0);
-	if (ret) {
-		dev_warn(dev, "Failed to read OCOTP nvmem cell (%d).\n", ret);
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to read OCOTP nvmem cell\n");
 
 	writel(FIELD_PREP(TASR_BUF_VREF_MASK,
 			  FIELD_GET(ANA0_BUF_VREF_MASK, ana0)) |

drivers/thermal/k3_bandgap.c

@@ -225,7 +225,6 @@ static int k3_bandgap_probe(struct platform_device *pdev)
 		devm_thermal_add_hwmon_sysfs(dev, data[id].tzd);
 	}
 
-	platform_set_drvdata(pdev, bgp);
 
 	return 0;
 

drivers/thermal/k3_j72xx_bandgap.c

@@ -502,8 +502,6 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)
 	writel(K3_VTM_ANYMAXT_OUTRG_ALERT_EN, data[0].bgp->cfg2_base +
 	       K3_VTM_MISC_CTRL_OFFSET);
 
-	platform_set_drvdata(pdev, bgp);
-
 	print_look_up_table(dev, ref_table);
 	/*
 	 * Now that the derived_table has the appropriate look up values