Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "No core changes this time around.

  New drivers:

   - New driver for Renesas R8A779H0 also known as R-Car V4M.

   - New driver for the Awinic AW9523/B I2C GPIO expander. I found this
     living out-of-tree in OpenWrt as an upstream attempt had stalled on
     the finishing line, so I picked it up and finished the job.

  Improvements:

   - The Nomadik pin control driver was for years re-used out of tree
     for the ST STA chips, and now the IP was re-used in a MIPS
     automotive SoC called MobilEyeq5, so it has been split in pin
     control and GPIO drivers so the latter can be reused by MobilEyeq5.
     (Along with a long list of cleanups)

   - A lot of overall cleanup and tidying up"

* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
  drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
  gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
  dt-bindings: pinctrl: qcom: update compatible name for match with driver
  pinctrl: aw9523: Make the driver tristate
  pinctrl: nomadik: fix dereference of error pointer
  gpio: nomadik: Back out some managed resources
  pinctrl: aw9523: Add proper terminator
  pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
  pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
  pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
  dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
  gpio: nomadik: Finish conversion to use firmware node APIs
  gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
  pinctrl: da9062: Add OF table
  dt-bindings: pinctrl: at91: add sam9x7
  pinctrl: ocelot: remove redundant assignment to variable ret
  gpio: nomadik: grab optional reset control and deassert it at probe
  gpio: nomadik: support mobileye,eyeq5-gpio
  gpio: nomadik: handle variadic GPIO count
  gpio: nomadik: support shared GPIO IRQs
  ...

Author: torvalds

Documentation/devicetree/bindings/gpio/gpio-nmk.txt

@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/st,nomadik-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nomadik GPIO controller
+
+description:
+  The Nomadik GPIO driver handles Nomadik SoC GPIO blocks. This block has also
+  been called ST STA2X11. On the Nomadik platform, this driver is intertwined
+  with pinctrl-nomadik.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    enum:
+      - st,nomadik-gpio
+      - mobileye,eyeq5-gpio
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-controller: true
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  gpio-bank:
+    description: System-wide GPIO bank index.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  st,supports-sleepmode:
+    description: Whether the controller can sleep or not.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  clocks:
+    maxItems: 1
+
+  gpio-ranges:
+    maxItems: 1
+
+  ngpios:
+    minimum: 0
+    maximum: 32
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#gpio-cells"
+  - gpio-controller
+  - interrupt-controller
+  - gpio-bank
+
+unevaluatedProperties: false
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mobileye,eyeq5-gpio
+    then:
+      properties:
+        st,supports-sleepmode: false
+
+examples:
+  - |
+    gpio@8012e080 {
+        compatible = "st,nomadik-gpio";
+        reg =  <0x8012e080 0x80>;
+        interrupts = <0 120 0x4>;
+        #gpio-cells = <2>;
+        gpio-controller;
+        interrupt-controller;
+        st,supports-sleepmode;
+        gpio-bank = <1>;
+    };

Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml

@@ -24,7 +24,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false

Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml

@@ -21,7 +21,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false

Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml

@@ -21,7 +21,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false

Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml

@@ -29,7 +29,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false

Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml

@@ -29,7 +29,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false

Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml

@@ -20,6 +20,7 @@ such as pull-up, multi drive, etc.
 Required properties for iomux controller:
 - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
 		or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl"
+		or "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl"
 - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
   configured in this periph mode. All the periph and bank need to be describe.
 
@@ -120,6 +121,7 @@ Some requirements for using atmel,at91rm9200-pinctrl binding:
 For each bank the required properties are:
 - compatible: "atmel,at91sam9x5-gpio" or "atmel,at91rm9200-gpio" or
   "microchip,sam9x60-gpio"
+  or "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio"
 - reg: physical base address and length of the controller's registers
 - interrupts: interrupt outputs from the controller
 - interrupt-controller: marks the device node as an interrupt controller

Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -0,0 +1,139 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/awinic,aw9523-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Awinic AW9523/AW9523B I2C GPIO Expander
+
+maintainers:
+  - AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
+
+description: |
+  The Awinic AW9523/AW9523B I2C GPIO Expander featuring 16 multi-function
+  I/O, 256 steps PWM mode and interrupt support.
+
+properties:
+  compatible:
+    const: awinic,aw9523-pinctrl
+
+  reg:
+    maxItems: 1
+
+  '#gpio-cells':
+    description: |
+      Specifying the pin number and flags, as defined in
+      include/dt-bindings/gpio/gpio.h
+    const: 2
+
+  gpio-controller: true
+
+  gpio-ranges:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  interrupts:
+    maxItems: 1
+    description: Specifies the INTN pin IRQ.
+
+  '#interrupt-cells':
+    description:
+      Specifies the PIN numbers and Flags, as defined in defined in
+      include/dt-bindings/interrupt-controller/irq.h
+    const: 2
+
+  reset-gpios:
+    maxItems: 1
+
+# PIN CONFIGURATION NODES
+patternProperties:
+  '-pins$':
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: /schemas/pinctrl/pincfg-node.yaml
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in
+          this subnode.
+        items:
+          pattern: "^gpio([0-9]|1[0-5])$"
+        minItems: 1
+        maxItems: 16
+
+      function:
+        description:
+          Specify the alternative function to be configured for the
+          specified pins.
+
+        enum: [ gpio, pwm ]
+
+      bias-disable: true
+      bias-pull-down: true
+      bias-pull-up: true
+      drive-open-drain: true
+      drive-push-pull: true
+      input-enable: true
+      input-disable: true
+      output-high: true
+      output-low: true
+
+    required:
+      - pins
+      - function
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  # Example configuration to drive pins for a keyboard matrix
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        aw9523: gpio-expander@58 {
+                compatible = "awinic,aw9523-pinctrl";
+                reg = <0x58>;
+                interrupt-parent = <&tlmm>;
+                interrupts = <50 IRQ_TYPE_EDGE_FALLING>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                gpio-ranges = <&tlmm 0 0 16>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+                reset-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+
+                keyboard-matrix-col-pins {
+                        pins = "gpio8", "gpio9", "gpio10", "gpio11",
+                               "gpio12", "gpio13", "gpio14", "gpio15";
+                        function = "gpio";
+                        input-disable;
+                        output-low;
+                };
+
+                keyboard-matrix-row-pins {
+                        pins = "gpio0", "gpio1", "gpio2", "gpio3",
+                               "gpio4", "gpio5", "gpio6", "gpio7";
+                        function = "gpio";
+                        bias-pull-up;
+                        drive-open-drain;
+                        input-enable;
+                };
+        };
+    };

Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml

@@ -93,7 +93,8 @@ properties:
 
           input-schmitt-disable: true
 
-          input-debounce: true
+          input-debounce:
+            maxItems: 1
 
           output-low: true