dt-bindings: Fix various typos

Corrected several typos in Documentation/devicetree/bindings files.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Link: https://lore.kernel.org/r/20240905151943.2792056-1-eleanor15x@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>

Author: eleanorLYJ

Documentation/devicetree/bindings/arm/arm,coresight-dummy-source.yaml

@@ -17,7 +17,7 @@ description: |
   The Coresight dummy source component is for the specific coresight source
   devices kernel don't have permission to access or configure. For some SOCs,
   there would be Coresight source trace components on sub-processor which
-  are conneted to AP processor via debug bus. For these devices, a dummy driver
+  are connected to AP processor via debug bus. For these devices, a dummy driver
   is needed to register them as Coresight source devices, so that paths can be
   created in the driver. It provides Coresight API for operations on dummy
   source devices, such as enabling and disabling them. It also provides the

Documentation/devicetree/bindings/cpu/idle-states.yaml

@@ -385,7 +385,7 @@ patternProperties:
 
           This property is required in idle state nodes of device tree meant
           for RISC-V systems. For more details on the suspend_type parameter
-          refer the SBI specifiation v0.3 (or higher) [7].
+          refer the SBI specification v0.3 (or higher) [7].
 
       local-timer-stop:
         description:

Documentation/devicetree/bindings/display/lvds.yaml

@@ -16,7 +16,7 @@ maintainers:
 description:
   This binding extends the data mapping defined in lvds-data-mapping.yaml.
   It supports reversing the bit order on the formats defined there in order
-  to accomodate for even more specialized data formats, since a variety of
+  to accommodate for even more specialized data formats, since a variety of
   data formats and layouts is used to drive LVDS displays.
 
 properties:

Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt

@@ -20,7 +20,7 @@ Optional properties:
 		memcpy channels in eDMA.
 
 Notes:
-When requesting channel via ti,dra7-dma-crossbar, the DMA clinet must request
+When requesting channel via ti,dra7-dma-crossbar, the DMA client must request
 the DMA event number as crossbar ID (input to the DMA crossbar).
 
 For ti,am335x-edma-crossbar: the meaning of parameters of dmas for clients:

Documentation/devicetree/bindings/iio/accel/lis302.txt

@@ -36,7 +36,7 @@ Optional properties for all bus drivers:
  - st,irq{1,2}-disable:		disable IRQ 1/2
  - st,irq{1,2}-ff-wu-1:		raise IRQ 1/2 on FF_WU_1 condition
  - st,irq{1,2}-ff-wu-2:		raise IRQ 1/2 on FF_WU_2 condition
- - st,irq{1,2}-data-ready:	raise IRQ 1/2 on data ready contition
+ - st,irq{1,2}-data-ready:	raise IRQ 1/2 on data ready condition
  - st,irq{1,2}-click:		raise IRQ 1/2 on click condition
  - st,irq-open-drain:		consider IRQ lines open-drain
  - st,irq-active-low:		make IRQ lines active low

Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml

@@ -60,7 +60,7 @@ properties:
       The 4th cell is a phandle to a node describing a set of CPUs this
       interrupt is affine to. The interrupt must be a PPI, and the node
       pointed must be a subnode of the "ppi-partitions" subnode. For
-      interrupt types other than PPI or PPIs that are not partitionned,
+      interrupt types other than PPI or PPIs that are not partitioned,
       this cell must be zero. See the "ppi-partitions" node description
       below.
 

Documentation/devicetree/bindings/leds/awinic,aw200xx.yaml

@@ -66,7 +66,7 @@ patternProperties:
             IMAXled = 160000 * (592 / 600.5) * (1 / max-current-switch-number)
           And the minimum output current formula:
             IMINled = 3300 * (592 / 600.5) * (1 / max-current-switch-number)
-          where max-current-switch-number is determinated by led configuration
+          where max-current-switch-number is determined by led configuration
           and depends on how leds are physically connected to the led driver.
 
 allOf:

Documentation/devicetree/bindings/mailbox/brcm,iproc-flexrm-mbox.txt

@@ -24,7 +24,7 @@ Required properties:
 		number of completion messages for which FlexRM will inject
 		one MSI interrupt to CPU.
 
-		The 3nd cell contains MSI timer value representing time for
+		The 3rd cell contains MSI timer value representing time for
 		which FlexRM will wait to accumulate N completion messages
 		where N is the value specified by 2nd cell above. If FlexRM
 		does not get required number of completion messages in time

Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml

@@ -16,7 +16,7 @@ description:
   can be connected to CMOS image sensors from various vendors, supporting both
   MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2
   or parallel. The hardware is capable of transmitting and receiving MIPI
-  interlaved data strams with data types or multiple virtual channel
+  interleaved data streams with data types or multiple virtual channel
   identifiers.
 
 allOf:

Documentation/devicetree/bindings/media/samsung,exynos4210-fimc.yaml

@@ -77,7 +77,7 @@ properties:
     $ref: /schemas/types.yaml#/definitions/uint32-array
     maxItems: 2
     description: |
-      An array specyfing minimum image size in pixels at the FIMC input and
+      An array specifying minimum image size in pixels at the FIMC input and
       output DMA, in the first and second cell respectively.  Default value
       is <16 16>.