Merge tag 'devicetree-fixes-for-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull devicetree fixes from Rob Herring:

 - Revert schema checks on %.dtb targets. This was problematic for some
   external build tools.

 - A few DT binding example fixes

 - Add back dropped 'enet-phy-lane-no-swap' Ethernet PHY property

 - Drop erroneous if/then schema in nxp,imx7-mipi-csi2

 - Add a quirk to fix some interrupt controllers use of 'interrupt-map'

* tag 'devicetree-fixes-for-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  Revert "kbuild: Enable DT schema checks for %.dtb targets"
  dt-bindings: bq25980: Fixup the example
  dt-bindings: input: gpio-keys: Fix interrupts in example
  dt-bindings: net: Reintroduce PHY no lane swap binding
  dt-bindings: media: nxp,imx7-mipi-csi2: Drop bad if/then schema
  of/irq: Add a quirk for controllers with their own definition of interrupt-map
  dt-bindings: iio: adc: exynos-adc: Fix node name in example

Author: torvalds

Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.yaml

@@ -136,7 +136,7 @@ examples:
         samsung,syscon-phandle = <&pmu_system_controller>;
 
         /* NTC thermistor is a hwmon device */
-        ncp15wb473 {
+        thermistor {
             compatible = "murata,ncp15wb473";
             pullup-uv = <1800000>;
             pullup-ohm = <47000>;

Documentation/devicetree/bindings/input/gpio-keys.yaml

@@ -142,7 +142,7 @@ examples:
         down {
             label = "GPIO Key DOWN";
             linux,code = <108>;
-            interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+            interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
         };
     };
 

Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml

@@ -79,6 +79,8 @@ properties:
 
             properties:
               data-lanes:
+                description:
+                  Note that 'fsl,imx7-mipi-csi2' only supports up to 2 data lines.
                 items:
                   minItems: 1
                   maxItems: 4
@@ -91,18 +93,6 @@ properties:
             required:
               - data-lanes
 
-            allOf:
-              - if:
-                  properties:
-                    compatible:
-                      contains:
-                        const: fsl,imx7-mipi-csi2
-                then:
-                  properties:
-                    data-lanes:
-                      items:
-                        maxItems: 2
-
       port@1:
         $ref: /schemas/graph.yaml#/properties/port
         description:

Documentation/devicetree/bindings/net/ethernet-phy.yaml

@@ -91,6 +91,14 @@ properties:
       compensate for the board being designed with the lanes
       swapped.
 
+  enet-phy-lane-no-swap:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      If set, indicates that PHY will disable swap of the
+      TX/RX lanes. This property allows the PHY to work correcly after
+      e.g. wrong bootstrap configuration caused by issues in PCB
+      layout design.
+
   eee-broken-100tx:
     $ref: /schemas/types.yaml#/definitions/flag
     description:

Documentation/devicetree/bindings/power/supply/bq25980.yaml

@@ -105,7 +105,7 @@ examples:
           reg = <0x65>;
           interrupt-parent = <&gpio1>;
           interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
-          ti,watchdog-timer = <0>;
+          ti,watchdog-timeout-ms = <0>;
           ti,sc-ocp-limit-microamp = <2000000>;
           ti,sc-ovp-limit-microvolt = <17800000>;
           monitored-battery = <&bat>;

Makefile

@@ -1374,17 +1374,17 @@ endif
 
 ifneq ($(dtstree),)
 
-%.dtb: dt_binding_check include/config/kernel.release scripts_dtc
-	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@ $(dtstree)/$*.dt.yaml
+%.dtb: include/config/kernel.release scripts_dtc
+	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
 
-%.dtbo: dt_binding_check include/config/kernel.release scripts_dtc
-	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@ $(dtstree)/$*.dt.yaml
+%.dtbo: include/config/kernel.release scripts_dtc
+	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
 
 PHONY += dtbs dtbs_install dtbs_check
 dtbs: include/config/kernel.release scripts_dtc
 	$(Q)$(MAKE) $(build)=$(dtstree)
 
-ifneq ($(filter dtbs_check %.dtb %.dtbo, $(MAKECMDGOALS)),)
+ifneq ($(filter dtbs_check, $(MAKECMDGOALS)),)
 export CHECK_DTBS=y
 dtbs: dt_binding_check
 endif

drivers/of/irq.c

@@ -76,6 +76,26 @@ struct device_node *of_irq_find_parent(struct device_node *child)
 }
 EXPORT_SYMBOL_GPL(of_irq_find_parent);
 
+/*
+ * These interrupt controllers abuse interrupt-map for unspeakable
+ * reasons and rely on the core code to *ignore* it (the drivers do
+ * their own parsing of the property).
+ *
+ * If you think of adding to the list for something *new*, think
+ * again. There is a high chance that you will be sent back to the
+ * drawing board.
+ */
+static const char * const of_irq_imap_abusers[] = {
+	"CBEA,platform-spider-pic",
+	"sti,platform-spider-pic",
+	"realtek,rtl-intc",
+	"fsl,ls1021a-extirq",
+	"fsl,ls1043a-extirq",
+	"fsl,ls1088a-extirq",
+	"renesas,rza1-irqc",
+	NULL,
+};
+
 /**
  * of_irq_parse_raw - Low level interrupt tree parsing
  * @addr:	address specifier (start of "reg" property of the device) in be32 format
@@ -159,12 +179,15 @@ int of_irq_parse_raw(const __be32 *addr, struct of_phandle_args *out_irq)
 		/*
 		 * Now check if cursor is an interrupt-controller and
 		 * if it is then we are done, unless there is an
-		 * interrupt-map which takes precedence.
+		 * interrupt-map which takes precedence except on one
+		 * of these broken platforms that want to parse
+		 * interrupt-map themselves for $reason.
 		 */
 		bool intc = of_property_read_bool(ipar, "interrupt-controller");
 
 		imap = of_get_property(ipar, "interrupt-map", &imaplen);
-		if (imap == NULL && intc) {
+		if (intc &&
+		    (!imap || of_device_compatible_match(ipar, of_irq_imap_abusers))) {
 			pr_debug(" -> got it !\n");
 			return 0;
 		}