i2c: nomadik: use bitops helpers

Constant register bit fields are declared using hardcoded hex values;
replace them by calls to BIT() and GENMASK(). Replace custom GEN_MASK()
macro by the generic FIELD_PREP(). Replace manual bit manipulations by
the generic FIELD_GET() macro.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Author: tleb

drivers/i2c/busses/i2c-nomadik.c

@@ -9,6 +9,7 @@
  * Author: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
  * Author: Sachin Verma <sachin.verma@st.com>
  */
+#include <linux/bitfield.h>
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/amba/bus.h>
@@ -42,54 +43,59 @@
 #define I2C_ICR		(0x038)
 
 /* Control registers */
-#define I2C_CR_PE		(0x1 << 0)	/* Peripheral Enable */
-#define I2C_CR_OM		(0x3 << 1)	/* Operating mode */
-#define I2C_CR_SAM		(0x1 << 3)	/* Slave addressing mode */
-#define I2C_CR_SM		(0x3 << 4)	/* Speed mode */
-#define I2C_CR_SGCM		(0x1 << 6)	/* Slave general call mode */
-#define I2C_CR_FTX		(0x1 << 7)	/* Flush Transmit */
-#define I2C_CR_FRX		(0x1 << 8)	/* Flush Receive */
-#define I2C_CR_DMA_TX_EN	(0x1 << 9)	/* DMA Tx enable */
-#define I2C_CR_DMA_RX_EN	(0x1 << 10)	/* DMA Rx Enable */
-#define I2C_CR_DMA_SLE		(0x1 << 11)	/* DMA sync. logic enable */
-#define I2C_CR_LM		(0x1 << 12)	/* Loopback mode */
-#define I2C_CR_FON		(0x3 << 13)	/* Filtering on */
-#define I2C_CR_FS		(0x3 << 15)	/* Force stop enable */
+#define I2C_CR_PE		BIT(0)		/* Peripheral Enable */
+#define I2C_CR_OM		GENMASK(2, 1)	/* Operating mode */
+#define I2C_CR_SAM		BIT(3)		/* Slave addressing mode */
+#define I2C_CR_SM		GENMASK(5, 4)	/* Speed mode */
+#define I2C_CR_SGCM		BIT(6)		/* Slave general call mode */
+#define I2C_CR_FTX		BIT(7)		/* Flush Transmit */
+#define I2C_CR_FRX		BIT(8)		/* Flush Receive */
+#define I2C_CR_DMA_TX_EN	BIT(9)		/* DMA Tx enable */
+#define I2C_CR_DMA_RX_EN	BIT(10)		/* DMA Rx Enable */
+#define I2C_CR_DMA_SLE		BIT(11)		/* DMA sync. logic enable */
+#define I2C_CR_LM		BIT(12)		/* Loopback mode */
+#define I2C_CR_FON		GENMASK(14, 13)	/* Filtering on */
+#define I2C_CR_FS		GENMASK(16, 15)	/* Force stop enable */
+
+/* Slave control register (SCR) */
+#define I2C_SCR_SLSU		GENMASK(31, 16)	/* Slave data setup time */
 
 /* Master controller (MCR) register */
-#define I2C_MCR_OP		(0x1 << 0)	/* Operation */
-#define I2C_MCR_A7		(0x7f << 1)	/* 7-bit address */
-#define I2C_MCR_EA10		(0x7 << 8)	/* 10-bit Extended address */
-#define I2C_MCR_SB		(0x1 << 11)	/* Extended address */
-#define I2C_MCR_AM		(0x3 << 12)	/* Address type */
-#define I2C_MCR_STOP		(0x1 << 14)	/* Stop condition */
-#define I2C_MCR_LENGTH		(0x7ff << 15)	/* Transaction length */
+#define I2C_MCR_OP		BIT(0)		/* Operation */
+#define I2C_MCR_A7		GENMASK(7, 1)	/* 7-bit address */
+#define I2C_MCR_EA10		GENMASK(10, 8)	/* 10-bit Extended address */
+#define I2C_MCR_SB		BIT(11)		/* Extended address */
+#define I2C_MCR_AM		GENMASK(13, 12)	/* Address type */
+#define I2C_MCR_STOP		BIT(14)		/* Stop condition */
+#define I2C_MCR_LENGTH		GENMASK(25, 15)	/* Transaction length */
 
 /* Status register (SR) */
-#define I2C_SR_OP		(0x3 << 0)	/* Operation */
-#define I2C_SR_STATUS		(0x3 << 2)	/* controller status */
-#define I2C_SR_CAUSE		(0x7 << 4)	/* Abort cause */
-#define I2C_SR_TYPE		(0x3 << 7)	/* Receive type */
-#define I2C_SR_LENGTH		(0x7ff << 9)	/* Transfer length */
+#define I2C_SR_OP		GENMASK(1, 0)	/* Operation */
+#define I2C_SR_STATUS		GENMASK(3, 2)	/* controller status */
+#define I2C_SR_CAUSE		GENMASK(6, 4)	/* Abort cause */
+#define I2C_SR_TYPE		GENMASK(8, 7)	/* Receive type */
+#define I2C_SR_LENGTH		GENMASK(19, 9)	/* Transfer length */
+
+/* Baud-rate counter register (BRCR) */
+#define I2C_BRCR_BRCNT1		GENMASK(31, 16)	/* Baud-rate counter 1 */
+#define I2C_BRCR_BRCNT2		GENMASK(15, 0)	/* Baud-rate counter 2 */
 
 /* Interrupt mask set/clear (IMSCR) bits */
-#define I2C_IT_TXFE		(0x1 << 0)
-#define I2C_IT_TXFNE		(0x1 << 1)
-#define I2C_IT_TXFF		(0x1 << 2)
-#define I2C_IT_TXFOVR		(0x1 << 3)
-#define I2C_IT_RXFE		(0x1 << 4)
-#define I2C_IT_RXFNF		(0x1 << 5)
-#define I2C_IT_RXFF		(0x1 << 6)
-#define I2C_IT_RFSR		(0x1 << 16)
-#define I2C_IT_RFSE		(0x1 << 17)
-#define I2C_IT_WTSR		(0x1 << 18)
-#define I2C_IT_MTD		(0x1 << 19)
-#define I2C_IT_STD		(0x1 << 20)
-#define I2C_IT_MAL		(0x1 << 24)
-#define I2C_IT_BERR		(0x1 << 25)
-#define I2C_IT_MTDWS		(0x1 << 28)
-
-#define GEN_MASK(val, mask, sb)  (((val) << (sb)) & (mask))
+#define I2C_IT_TXFE		BIT(0)
+#define I2C_IT_TXFNE		BIT(1)
+#define I2C_IT_TXFF		BIT(2)
+#define I2C_IT_TXFOVR		BIT(3)
+#define I2C_IT_RXFE		BIT(4)
+#define I2C_IT_RXFNF		BIT(5)
+#define I2C_IT_RXFF		BIT(6)
+#define I2C_IT_RFSR		BIT(16)
+#define I2C_IT_RFSE		BIT(17)
+#define I2C_IT_WTSR		BIT(18)
+#define I2C_IT_MTD		BIT(19)
+#define I2C_IT_STD		BIT(20)
+#define I2C_IT_MAL		BIT(24)
+#define I2C_IT_BERR		BIT(25)
+#define I2C_IT_MTDWS		BIT(28)
 
 /* some bits in ICR are reserved */
 #define I2C_CLEAR_ALL_INTS	0x131f007f
@@ -128,6 +134,12 @@ enum i2c_operation {
 	I2C_READ = 0x01
 };
 
+enum i2c_operating_mode {
+	I2C_OM_SLAVE,
+	I2C_OM_MASTER,
+	I2C_OM_MASTER_OR_SLAVE,
+};
+
 /**
  * struct i2c_nmk_client - client specific data
  * @slave_adr: 7-bit slave address
@@ -284,7 +296,10 @@ static int init_hw(struct nmk_i2c_dev *priv)
 }
 
 /* enable peripheral, master mode operation */
-#define DEFAULT_I2C_REG_CR	((1 << 1) | I2C_CR_PE)
+#define DEFAULT_I2C_REG_CR	(FIELD_PREP(I2C_CR_OM, I2C_OM_MASTER) | I2C_CR_PE)
+
+/* grab top three bits from extended I2C addresses */
+#define ADR_3MSB_BITS		GENMASK(9, 7)
 
 /**
  * load_i2c_mcr_reg() - load the MCR register
@@ -296,41 +311,42 @@ static u32 load_i2c_mcr_reg(struct nmk_i2c_dev *priv, u16 flags)
 	u32 mcr = 0;
 	unsigned short slave_adr_3msb_bits;
 
-	mcr |= GEN_MASK(priv->cli.slave_adr, I2C_MCR_A7, 1);
+	mcr |= FIELD_PREP(I2C_MCR_A7, priv->cli.slave_adr);
 
 	if (unlikely(flags & I2C_M_TEN)) {
 		/* 10-bit address transaction */
-		mcr |= GEN_MASK(2, I2C_MCR_AM, 12);
+		mcr |= FIELD_PREP(I2C_MCR_AM, 2);
 		/*
 		 * Get the top 3 bits.
 		 * EA10 represents extended address in MCR. This includes
 		 * the extension (MSB bits) of the 7 bit address loaded
 		 * in A7
 		 */
-		slave_adr_3msb_bits = (priv->cli.slave_adr >> 7) & 0x7;
+		slave_adr_3msb_bits = FIELD_GET(ADR_3MSB_BITS,
+						priv->cli.slave_adr);
 
-		mcr |= GEN_MASK(slave_adr_3msb_bits, I2C_MCR_EA10, 8);
+		mcr |= FIELD_PREP(I2C_MCR_EA10, slave_adr_3msb_bits);
 	} else {
 		/* 7-bit address transaction */
-		mcr |= GEN_MASK(1, I2C_MCR_AM, 12);
+		mcr |= FIELD_PREP(I2C_MCR_AM, 1);
 	}
 
 	/* start byte procedure not applied */
-	mcr |= GEN_MASK(0, I2C_MCR_SB, 11);
+	mcr |= FIELD_PREP(I2C_MCR_SB, 0);
 
 	/* check the operation, master read/write? */
 	if (priv->cli.operation == I2C_WRITE)
-		mcr |= GEN_MASK(I2C_WRITE, I2C_MCR_OP, 0);
+		mcr |= FIELD_PREP(I2C_MCR_OP, I2C_WRITE);
 	else
-		mcr |= GEN_MASK(I2C_READ, I2C_MCR_OP, 0);
+		mcr |= FIELD_PREP(I2C_MCR_OP, I2C_READ);
 
 	/* stop or repeated start? */
 	if (priv->stop)
-		mcr |= GEN_MASK(1, I2C_MCR_STOP, 14);
+		mcr |= FIELD_PREP(I2C_MCR_STOP, 1);
 	else
-		mcr &= ~(GEN_MASK(1, I2C_MCR_STOP, 14));
+		mcr &= ~FIELD_PREP(I2C_MCR_STOP, 1);
 
-	mcr |= GEN_MASK(priv->cli.count, I2C_MCR_LENGTH, 15);
+	mcr |= FIELD_PREP(I2C_MCR_LENGTH, priv->cli.count);
 
 	return mcr;
 }
@@ -383,7 +399,7 @@ static void setup_i2c_controller(struct nmk_i2c_dev *priv)
 	slsu += 1;
 
 	dev_dbg(&priv->adev->dev, "calculated SLSU = %04x\n", slsu);
-	writel(slsu << 16, priv->virtbase + I2C_SCR);
+	writel(FIELD_PREP(I2C_SCR_SLSU, slsu), priv->virtbase + I2C_SCR);
 
 	/*
 	 * The spec says, in case of std. mode the divider is
@@ -399,8 +415,8 @@ static void setup_i2c_controller(struct nmk_i2c_dev *priv)
 	 * plus operation. Currently we do not supprt high speed mode
 	 * so set brcr1 to 0.
 	 */
-	brcr1 = 0 << 16;
-	brcr2 = (i2c_clk / (priv->clk_freq * div)) & 0xffff;
+	brcr1 = FIELD_PREP(I2C_BRCR_BRCNT1, 0);
+	brcr2 = FIELD_PREP(I2C_BRCR_BRCNT2, i2c_clk / (priv->clk_freq * div));
 
 	/* set the baud rate counter register */
 	writel((brcr1 | brcr2), priv->virtbase + I2C_BRCR);
@@ -414,12 +430,13 @@ static void setup_i2c_controller(struct nmk_i2c_dev *priv)
 	if (priv->sm > I2C_FREQ_MODE_FAST) {
 		dev_err(&priv->adev->dev,
 			"do not support this mode defaulting to std. mode\n");
-		brcr2 = i2c_clk / (I2C_MAX_STANDARD_MODE_FREQ * 2) & 0xffff;
+		brcr2 = FIELD_PREP(I2C_BRCR_BRCNT2,
+				   i2c_clk / (I2C_MAX_STANDARD_MODE_FREQ * 2));
 		writel((brcr1 | brcr2), priv->virtbase + I2C_BRCR);
-		writel(I2C_FREQ_MODE_STANDARD << 4,
-				priv->virtbase + I2C_CR);
+		writel(FIELD_PREP(I2C_CR_SM, I2C_FREQ_MODE_STANDARD),
+		       priv->virtbase + I2C_CR);
 	}
-	writel(priv->sm << 4, priv->virtbase + I2C_CR);
+	writel(FIELD_PREP(I2C_CR_SM, priv->sm), priv->virtbase + I2C_CR);
 
 	/* set the Tx and Rx FIFO threshold */
 	writel(priv->tft, priv->virtbase + I2C_TFTR);
@@ -583,13 +600,8 @@ static int nmk_i2c_xfer_one(struct nmk_i2c_dev *priv, u16 flags)
 		u32 cause;
 
 		i2c_sr = readl(priv->virtbase + I2C_SR);
-		/*
-		 * Check if the controller I2C operation status
-		 * is set to ABORT(11b).
-		 */
-		if (((i2c_sr >> 2) & 0x3) == 0x3) {
-			/* get the abort cause */
-			cause =	(i2c_sr >> 4) & 0x7;
+		if (FIELD_GET(I2C_SR_STATUS, i2c_sr) == I2C_ABORT) {
+			cause = FIELD_GET(I2C_SR_CAUSE, i2c_sr);
 			dev_err(&priv->adev->dev, "%s\n",
 				cause >= ARRAY_SIZE(abort_causes) ?
 				"unknown reason" :
@@ -730,7 +742,7 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg)
 	misr = readl(priv->virtbase + I2C_MISR);
 
 	src = __ffs(misr);
-	switch ((1 << src)) {
+	switch (BIT(src)) {
 
 	/* Transmit FIFO nearly empty interrupt */
 	case I2C_IT_TXFNE:
@@ -824,15 +836,18 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg)
 	 * during the transaction.
 	 */
 	case I2C_IT_BERR:
+	{
+		u32 sr;
+
+		sr = readl(priv->virtbase + I2C_SR);
 		priv->result = -EIO;
-		/* get the status */
-		if (((readl(priv->virtbase + I2C_SR) >> 2) & 0x3) == I2C_ABORT)
+		if (FIELD_GET(I2C_SR_STATUS, sr) == I2C_ABORT)
 			init_hw(priv);
 
 		i2c_set_bit(priv->virtbase + I2C_ICR, I2C_IT_BERR);
 		complete(&priv->xfer_complete);
-
-		break;
+	}
+	break;
 
 	/*
 	 * Tx FIFO overrun interrupt.