Merge branches 'clk-st', 'clk-si' and 'clk-hisilicon' into clk-next

 - Stop using clock-output-names in ST clk drivers

* clk-st:
  dt-bindings: clock: st: clkgen-fsyn: add new introduced compatible
  clk: st: clkgen-fsyn: embed soc clock outputs within compatible data
  dt-bindings: clock: st: clkgen-pll: add new introduced compatible
  clk: st: clkgen-pll: embed soc clock outputs within compatible data
  dt-bindings: clock: st: flexgen: add new introduced compatible
  clk: st: flexgen: embed soc clock outputs within compatible data
  clk: st: clkgen-pll: remove unused variable of struct clkgen_pll

* clk-si:
  clk: si5341: Add sysfs properties to allow checking/resetting device faults
  clk: si5341: Add silabs,iovdd-33 property
  clk: si5341: Add silabs,xaxb-ext-clk property
  clk: si5341: Allow different output VDD_SEL values
  clk: si5341: Update initialization magic
  clk: si5341: Check for input clock presence and PLL lock on startup
  clk: si5341: Avoid divide errors due to bogus register contents
  clk: si5341: Wait for DEVICE_READY on startup
  dt-bindings: clock: clk-si5341: Add new attributes

* clk-hisilicon:
  clk: hisilicon: Add clock driver for hi3559A SoC
  dt-bindings: Document the hi3559a clock bindings

Author: bebarino

Documentation/devicetree/bindings/clock/hisilicon,hi3559av100-clock.yaml

@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/hisilicon,hi3559av100-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Hisilicon SOC Clock for HI3559AV100
+
+maintainers:
+  - Dongjiu Geng <gengdongjiu@huawei.com>
+
+description: |
+  Hisilicon SOC clock control module which supports the clocks, resets and
+  power domains on HI3559AV100.
+
+  See also:
+    dt-bindings/clock/hi3559av100-clock.h
+
+properties:
+  compatible:
+    enum:
+      - hisilicon,hi3559av100-clock
+      - hisilicon,hi3559av100-shub-clock
+
+  reg:
+    minItems: 1
+    maxItems: 2
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 2
+    description: |
+      First cell is reset request register offset.
+      Second cell is bit offset in reset request register.
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+  - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        clock-controller@12010000 {
+            compatible = "hisilicon,hi3559av100-clock";
+            #clock-cells = <1>;
+            #reset-cells = <2>;
+            reg = <0x0 0x12010000 0x0 0x10000>;
+        };
+    };
+...

Documentation/devicetree/bindings/clock/silabs,si5341.txt

@@ -24,9 +24,8 @@ it.
 
 The device type, speed grade and revision are determined runtime by probing.
 
-The driver currently only supports XTAL input mode, and does not support any
-fancy input configurations. They can still be programmed into the chip and
-the driver will leave them "as is".
+The driver currently does not support any fancy input configurations. They can
+still be programmed into the chip and the driver will leave them "as is".
 
 ==I2C device node==
 
@@ -45,9 +44,9 @@ Required properties:
 	corresponding to inputs. Use a fixed clock for the "xtal" input.
 	At least one must be present.
 - clock-names: One of: "xtal", "in0", "in1", "in2"
-- vdd-supply: Regulator node for VDD
 
 Optional properties:
+- vdd-supply: Regulator node for VDD
 - vdda-supply: Regulator node for VDDA
 - vdds-supply: Regulator node for VDDS
 - silabs,pll-m-num, silabs,pll-m-den: Numerator and denominator for PLL
@@ -60,7 +59,14 @@ Optional properties:
   be initialized, and always performs the soft-reset routine. Since this will
   temporarily stop all output clocks, don't do this if the chip is generating
   the CPU clock for example.
+- silabs,xaxb-ext-clk: When present, indicates that the XA/XB pins are used
+  in EXTCLK (external reference clock) rather than XTAL (crystal) mode.
 - interrupts: Interrupt for INTRb pin.
+- silabs,iovdd-33: When present, indicates that the I2C lines are using 3.3V
+  rather than 1.8V thresholds.
+- vddoX-supply (where X is an output index): Regulator node for VDDO for the
+  specified output. The driver selects the output VDD_SEL setting based on this
+  voltage.
 - #address-cells: shall be set to 1.
 - #size-cells: shall be set to 0.
 
@@ -77,8 +83,6 @@ Required child node properties:
 - reg: number of clock output.
 
 Optional child node properties:
-- vdd-supply: Regulator node for VDD for this output. The driver selects default
-	values for common-mode and amplitude based on the voltage.
 - silabs,format: Output format, one of:
 	1 = differential (defaults to LVDS levels)
 	2 = low-power (defaults to HCSL levels)

Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt

@@ -10,7 +10,10 @@ Required properties:
 
 - compatible : shall be:
 	"st,clkgen-pll0"
+	"st,clkgen-pll0-a0"
+	"st,clkgen-pll0-c0"
 	"st,clkgen-pll1"
+	"st,clkgen-pll1-c0"
 	"st,stih407-clkgen-plla9"
 	"st,stih418-clkgen-plla9"
 

Documentation/devicetree/bindings/clock/st/st,flexgen.txt

@@ -64,6 +64,16 @@ Required properties:
   audio use case)
   "st,flexgen-video", "st,flexgen" (enable clock propagation on parent
 					and activate synchronous mode)
+  "st,flexgen-stih407-a0"
+  "st,flexgen-stih410-a0"
+  "st,flexgen-stih407-c0"
+  "st,flexgen-stih410-c0"
+  "st,flexgen-stih418-c0"
+  "st,flexgen-stih407-d0"
+  "st,flexgen-stih410-d0"
+  "st,flexgen-stih407-d2"
+  "st,flexgen-stih418-d2"
+  "st,flexgen-stih407-d3"
 
 - #clock-cells : from common clock binding; shall be set to 1 (multiple clock
   outputs).

Documentation/devicetree/bindings/clock/st/st,quadfs.txt

@@ -12,6 +12,9 @@ This binding uses the common clock binding[1].
 Required properties:
 - compatible : shall be:
   "st,quadfs"
+  "st,quadfs-d0"
+  "st,quadfs-d2"
+  "st,quadfs-d3"
   "st,quadfs-pll"