Merge branch 'togreg' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git

Author: sfrothwell

Documentation/ABI/testing/sysfs-bus-iio

@@ -2254,3 +2254,21 @@ Description:
 		If a label is defined for this event add that to the event
 		specific attributes. This is useful for userspace to be able to
 		better identify an individual event.
+
+What:		/sys/.../events/in_accel_gesture_tap_wait_timeout
+KernelVersion:	6.7
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Enable tap gesture confirmation with timeout.
+
+What:		/sys/.../events/in_accel_gesture_tap_wait_dur
+KernelVersion:	6.7
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Timeout value in seconds for tap gesture confirmation.
+
+What:		/sys/.../events/in_accel_gesture_tap_wait_dur_available
+KernelVersion:	6.7
+Contact:	linux-iio@vger.kernel.org
+Description:
+		List of available timeout value for tap gesture confirmation.

Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml

@@ -0,0 +1,139 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim MAX34408/MAX34409 current monitors with overcurrent control
+
+maintainers:
+  - Ivan Mikhaylov <fr0st61te@gmail.com>
+
+description: |
+  The MAX34408/MAX34409 are two- and four-channel current monitors that are
+  configured and monitored with a standard I2C/SMBus serial interface. Each
+  unidirectional current sensor offers precision high-side operation with a
+  low full-scale sense voltage. The devices automatically sequence through
+  two or four channels and collect the current-sense samples and average them
+  to reduce the effect of impulse noise. The raw ADC samples are compared to
+  user-programmable digital thresholds to indicate overcurrent conditions.
+  Overcurrent conditions trigger a hardware output to provide an immediate
+  indication to shut down any necessary external circuitry.
+
+  Specifications about the devices can be found at:
+  https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf
+
+properties:
+  compatible:
+    enum:
+      - maxim,max34408
+      - maxim,max34409
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  powerdown-gpios:
+    description:
+      Shutdown Output. Open-drain output. This output transitions to high impedance
+      when any of the digital comparator thresholds are exceeded as long as the ENA
+      pin is high.
+    maxItems: 1
+
+  powerdown-status-gpios:
+    description:
+      SHTDN Enable Input. CMOS digital input. Connect to GND to clear the latch and
+      unconditionally deassert (force low) the SHTDN output and reset the shutdown
+      delay. Connect to VDD to enable normal latch operation of the SHTDN output.
+    maxItems: 1
+
+  vdd-supply: true
+
+patternProperties:
+  "^channel@[0-3]$":
+    $ref: adc.yaml
+    type: object
+    description:
+      Represents the internal channels of the ADC.
+
+    properties:
+      reg:
+        items:
+          - minimum: 0
+            maximum: 3
+
+      maxim,rsense-val-micro-ohms:
+        description:
+          Adjust the Rsense value to monitor higher or lower current levels for
+          input.
+        enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000]
+        default: 1000
+
+    required:
+      - reg
+      - maxim,rsense-val-micro-ohms
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: maxim,max34408
+    then:
+      patternProperties:
+        "^channel@[2-3]$": false
+        "^channel@[0-1]$":
+          properties:
+            reg:
+              maximum: 1
+    else:
+      patternProperties:
+        "^channel@[0-3]$":
+          properties:
+            reg:
+              maximum: 3
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        adc@1e {
+              compatible = "maxim,max34409";
+              reg = <0x1e>;
+              powerdown-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+              powerdown-status-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+
+              #address-cells = <1>;
+              #size-cells = <0>;
+
+              channel@0 {
+                  reg = <0x0>;
+                  maxim,rsense-val-micro-ohms = <5000>;
+              };
+
+              channel@1 {
+                  reg = <0x1>;
+                  maxim,rsense-val-micro-ohms = <10000>;
+             };
+        };
+    };

Documentation/devicetree/bindings/iio/imu/bosch,bmi323.yaml

@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/imu/bosch,bmi323.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bosch BMI323 6-Axis IMU
+
+maintainers:
+  - Jagath Jog J <jagathjog1996@gmail.com>
+
+description:
+  BMI323 is a 6-axis inertial measurement unit that supports acceleration and
+  gyroscopic measurements with hardware fifo buffering. Sensor also provides
+  events information such as motion, steps, orientation, single and double
+  tap detection.
+
+properties:
+  compatible:
+    const: bosch,bmi323
+
+  reg:
+    maxItems: 1
+
+  vdd-supply: true
+  vddio-supply: true
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      enum:
+        - INT1
+        - INT2
+
+  drive-open-drain:
+    description:
+      set if the specified interrupt pin should be configured as
+      open drain. If not set, defaults to push-pull.
+
+  mount-matrix:
+    description:
+      an optional 3x3 mounting rotation matrix.
+
+required:
+  - compatible
+  - reg
+  - vdd-supply
+  - vddio-supply
+
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    // Example for I2C
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imu@68 {
+            compatible = "bosch,bmi323";
+            reg = <0x68>;
+            vddio-supply = <&vddio>;
+            vdd-supply = <&vdd>;
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+            interrupt-names = "INT1";
+        };
+    };

MAINTAINERS

@@ -3640,6 +3640,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/accel/bosch,bma400.yaml
 F:	drivers/iio/accel/bma400*
 
+BOSCH SENSORTEC BMI323 IMU IIO DRIVER
+M:	Jagath Jog J <jagathjog1996@gmail.com>
+L:	linux-iio@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/iio/imu/bosch,bma400.yaml
+F:	drivers/iio/imu/bmi323/
+
 BPF JIT for ARM
 M:	Russell King <linux@armlinux.org.uk>
 M:	Puranjay Mohan <puranjay12@gmail.com>

drivers/base/property.c

@@ -473,7 +473,7 @@ int fwnode_property_match_string(const struct fwnode_handle *fwnode,
 	const char **values;
 	int nval, ret;
 
-	nval = fwnode_property_read_string_array(fwnode, propname, NULL, 0);
+	nval = fwnode_property_string_array_count(fwnode, propname);
 	if (nval < 0)
 		return nval;
 
@@ -498,6 +498,41 @@ int fwnode_property_match_string(const struct fwnode_handle *fwnode,
 }
 EXPORT_SYMBOL_GPL(fwnode_property_match_string);
 
+/**
+ * fwnode_property_match_property_string - find a property string value in an array and return index
+ * @fwnode: Firmware node to get the property of
+ * @propname: Name of the property holding the string value
+ * @array: String array to search in
+ * @n: Size of the @array
+ *
+ * Find a property string value in a given @array and if it is found return
+ * the index back.
+ *
+ * Return: index, starting from %0, if the string value was found in the @array (success),
+ *	   %-ENOENT when the string value was not found in the @array,
+ *	   %-EINVAL if given arguments are not valid,
+ *	   %-ENODATA if the property does not have a value,
+ *	   %-EPROTO or %-EILSEQ if the property is not a string,
+ *	   %-ENXIO if no suitable firmware interface is present.
+ */
+int fwnode_property_match_property_string(const struct fwnode_handle *fwnode,
+	const char *propname, const char * const *array, size_t n)
+{
+	const char *string;
+	int ret;
+
+	ret = fwnode_property_read_string(fwnode, propname, &string);
+	if (ret)
+		return ret;
+
+	ret = match_string(array, n, string);
+	if (ret < 0)
+		ret = -ENOENT;
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(fwnode_property_match_property_string);
+
 /**
  * fwnode_property_get_reference_args() - Find a reference with arguments
  * @fwnode:	Firmware node where to look for the reference

drivers/iio/adc/Kconfig

@@ -745,6 +745,17 @@ config MAX1363
 	  To compile this driver as a module, choose M here: the module will be
 	  called max1363.
 
+config MAX34408
+	tristate "Maxim max34408/max344089 ADC driver"
+	depends on I2C
+	help
+	  Say yes here to build support for Maxim max34408/max34409 current sense
+	  monitor with 8-bits ADC interface with overcurrent delay/threshold and
+	  shutdown delay.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called max34408.
+
 config MAX77541_ADC
 	tristate "Analog Devices MAX77541 ADC driver"
 	depends on MFD_MAX77541

drivers/iio/adc/Makefile

@@ -68,6 +68,7 @@ obj-$(CONFIG_MAX11205) += max11205.o
 obj-$(CONFIG_MAX11410) += max11410.o
 obj-$(CONFIG_MAX1241) += max1241.o
 obj-$(CONFIG_MAX1363) += max1363.o
+obj-$(CONFIG_MAX34408) += max34408.o
 obj-$(CONFIG_MAX77541_ADC) += max77541-adc.o
 obj-$(CONFIG_MAX9611) += max9611.o
 obj-$(CONFIG_MCP320X) += mcp320x.o